Mitel Inter-Tel Axxess Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 384

Mitel Inter-Tel Axxess Скачать руководство пользователя страница 102

Page 86

System Hardware

Inter-Tel

®

Axxess

®

Administrator Guide — Issue 11.0, May 2008

Default Inter-Tel Endpoint Feature Buttons

Default Inter-Tel Endpoint Feature Buttons

When the system is in the default state, all endpoints are in the same keymap group and have
the following feature buttons. Feature code descriptions start on

. (The Special button

is represented by buttons with

on the Inter-Tel endpoint.)

∞

Table 10.

Default Feature Buttons

BUTTON

FUNCTION

CALL BUTTONS 1-4

Selects an outgoing trunk, if idle, or answers a call on the button.

IC

Selects a voice channel or picks up a holding or camped-on intercom call.

DND

Programmable button 1: Do-Not-Disturb On/Off (372)

PROGRAMMABLE
BUTTONS 2-6, 14-16,
18, and 21-35

Undefined values. Can be programmed with any feature code, trunk access code, or
extension number, or can be programmed as a station or system speed-dial bin.

CNF

Programmable Button 7: Conference (5)

HOLD

Programmable Button 8: Individual Hold (336)

TRANSFER

Programmable Button 9: Transfer to Ring (345)

SYS SPD

Programmable Button 10: System Speed Dial (381)

REDIAL

Programmable Button 11: Redial (380)

PAGE

Programmable Button 12: Page (7)

QUEUE

Programmable Button 13: Queue Request (6)

MUSIC

Programmable Button 17: Background Music (313)

PAGE ZONE 1

Programmable Button 19: Selects Page Zone 1 for making a page.

STN SPEED DIAL

Programmable Button 20: Station Speed Dial (382)

FWD

Call Forward All Calls (355) Also used for canceling Call Forward.

SPECIAL

Signals the system to expect a feature code.

ANSWER

Answer (351)

OUTGOING

Selects a trunk for placing an outgoing call using the station’s Outgoing Call feature (8).

SPEAKER

Speakerphone On/Off

MSG

Message (365) – Also retrieves messages when the flashing MSG button is pressed.

MUTE

Microphone Mute On/Off (314) (This is a fixed-function button on digital endpoints.)

DATA

Data (340)

STATION SPEED DIAL
KEYS 0-9

Used for storing and dialing one station speed-dial number each.

UNDEFINED

Some analog endpoints have several undefined buttons that can be programmed as
desired.

«
...
100
101
102
103
104
...
»

Содержание Inter-Tel Axxess

































































































































































































































































































































































































Отзывы:

Нет отзывов