Mitek TWIN-AXIS Скачать руководство пользователя страница 12

Страница: 12 / 73

Original Instructions: 001059 DRAFT

xii

Twin-Axis

Sheathing Saw: Safety

Lockout/Tagout

Lockout/Tagout Guidelines

Lockout/tagout all energized systems before performing maintenance on them.

All lockout/tagout guidelines must be met according to OSHA 29 CFR

1910.147.

A specific procedure should be included in your company’s energy

control program. This manual is not intended to replace your company’s de-

energizing or lockout/tagout procedure required by OSHA, but merely to provide

general guidance.
The term “lockout,” as used in this manual, means placing a lockout device, such

as a keyed padlock, on any and all energy sources to ensure that the energy

isolating device and the equipment being controlled cannot be re-energized or

operated until the lockout device is removed. The photos on page xiii show

where

the electrical disconnects are located for this machine.

• Energy sources include electrical, mechanical, hydraulic, pneumatic,

chemical, thermal, or other energy.

• In the case of electrical energy sources, the main power and control power

to the machinery must be turned off and physically locked in the Off position.

• Before performing maintenance on the pneumatic or hydraulic systems,

bleed the lines prior to lockout/tagout to eliminate pressure.

If more than one person is working in a restricted zone, use a group lockout

device that will allow each person to use a lock that can be removed only by the

person performing the maintenance.
“Tagout” means that a prominent warning is securely fastened to an energy-

isolating device to indicate that the equipment shall not be operated.
Whenever you see this symbol, lockout/tagout!

Содержание TWIN-AXIS










































































Результаты поиска

Содержание TWIN-AXIS

Отзывы:

Mitek TWIN-AXIS, Руководство по эксплуатации оборудования, Страница: 12 / 73

Результаты поиска

Содержание TWIN-AXIS

Отзывы: