ConfigurAtion
When connecting the EP-11S to the back of the
Eleven Rack, it is necessary to set the Eleven Rack
to correctly recognize the pedal in order to get the
best response. Turn on the Eleven Rack and hold
the edit button for a few seconds to bring up the
option menu on the display. Turn the scroll knob
until ‘External Pedals’ is highlighted and then press
the illuminated SW1 ‘select’ button. If necessary,
turn the scroll knob again until ‘Expression Pedals’ is
highlighted. Turn the illuminated ‘Pedal Type’ knob
until ‘Pedal Type: EP-11’ is displayed.
After selecting the pedal type, the start and stop
positions need to be calibrated. Press the illuminated
SW2 ‘calibrate’ button. Set the pedal to heel down
and then press the SW1 ‘next’ button. Set the pedal
to toe down and press next again. To test that the
Eleven Rack is detecting the pedal, move the rocker
up and down and make sure that the green SW2
‘active’ light illuminates. If not, check that you are
using the correct cable, and it is connected correctly,
then repeat the setup procedure. Press SW1 ‘save’
to store the settings, and setup is complete.
Adju
mEnts
The tension of the rocker can be adjusted using the
tension adjustment screw on the rear of the pedal
between the rocker and the base. Use the hex key
provided to tighten the adjustment screw until the
pedal remains in place. It maybe necessary to adjust
this screw every once in a while to compensate for
use and environmental conditions such as very hot or
Mission Engin
ring
Inc.
www.missionengineering.com [email protected]
©
Mission Engineering Inc. 2013. All rights reserved. Trademarks,
registered trademarks, product names, logos and other materials are
the property of their respective owners.
SAf
y
In
ru
ions
Read, Keep & Follow these instructions
Heed all warnings
Clean only with dry cloth
Do not use this apparatus near water
Do not expose the apparatus to dripping or
splashing and ensure that no objects filled with
liquids, shall be placed on the apparatus
WARNING: To reduce the risk of fire or electric
shock do not expose this apparatus to rain or
moisture
Unplug this apparatus during lightning storms or
when unused for long periods of time
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions
Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat
Only use attachments/accessories specified by
the manufacturer
Prolonged listening at high volume levels may
cause irreparable hearing loss and/or damage.
Always be sure to practice “safe listening.”
Refer all servicing to qualified service personnel.
Service is required when the apparatus has been
damaged in any way, such as:
- power-supply cord or plug is damaged
- liquid has been spilled or objects have fallen
into the apparatus
- the unit has been exposed to rain or moisture.
- the unit is dropped or the enclosure is
damaged
- the unit does not operate normally or changes
in performance in a significant way
cold weather, when the pedal has been stored for a
long period, or after shipping. Replacement hex keys
are available.
The switch sensitivity on the EP-11S can be adjusted
by lowering or raising the switch in the chassis.
Use spacers and washers provided to lower the
switch making it harder to press. Remove spacers
and washers to raise the switch making it easier to
press. When replacing the switch, be careful not to
over tighten the lock nut and damage the switch.
Ecifi
tions
Electrical Specifications
Potentiometer
Internal resistance - 10K Ohm
Taper - Linear
Polarity - Tip to wiper/ring to wiper , switch selectable
Function - Voltage Divider
Usage rating > 1M cycles
Switch
Type - Latching
Function - Toggles tip between ring and sleeve
Dimensions
Base length at longest point
-
9.9”
Base width at widest point - 4.0”
Height at highest point including feet - 3.25”
Pedal length - 8.7”
Pedal width at widest point - 3.0”
Pedal width at narrowest point - 2.3”
Weight - 3.5lbs
