User Guide
Operation Indicator Sounds and Lights
Sounds
Lights
Meaning
Successful Operation
Successful Programming
Operation Error
Code Input Error; System Shuts
Down for 45 seconds
Low Battery Power
Default Setting Restored
In Programming Mode
1 Beep
2 Long Beeps
3 Beeps
5 Beeps
10 Rapid Beeps
Flashes Green Once
Flashes Green Twice
Flashes Red 3 Times
Flashes Red 5 Times
Flashes Red 10 Times
Flashes Orange 3 Times
Flashes Orange Slowly
Do not use any chemical liquid or lubricating oil with additives to clean the lock body.
It will damage the surface or even mainboard.
Operational Interface
Battery Lid
Slide the lid to change the batteries.
Battery Holder
Four AA (1.5 V) alkaline batteries.
R Button (Reset)
Restore default settings.
Turn-piece
To lock/unlock the lockset from inside.
Programming Button
Programming button is for entering codes,
clearing errors and setting function.
It is also used to lock the door.
Number Buttons
To enter user codes. Each user code is
4–10 digits in length.
Cylinder
To lock/unlock the lockset from outside.
Washer
Prevents water from permeating into lockset.
Operating Instructions
Restore Default Settings
Press
R
Note:
Press the button for more than 5 seconds; the programming
is reset back to the original factory codes once you hear 3
long beeps.
After restoring default settings, you must run the door
handing identifying process (#1) again before
programming any other functions.
R
R
Reset
button
11
Delete an Existing User Code
2
Enter the UC
you want to
delete
Delete All User Codes at Once
3
Default programming code (PC): 0000
Default user code (UC): 1234
Your new programming code (PC) ____________
Your new user code (UC) ___________________
The same programming code and user code cannot be accepted.
The lock will cease operation if unauthorized codes are entered over 5 times.
The system will unfreeze after 45 seconds.
DO THIS FIRST
Door Handing Identification Process
The lock needs to learn if your door is a right-
or left-handed.
handed
0
!
Toggle Auto-Lock On/Off
5
Note:
Repeat the steps in #6 to cancel the auto-locking function.
The preset delay-time is 30 seconds, you can change the time by following instructions #7.
6
Set Auto-Lock Time Delay
Note:
10–99 seconds delay-time available.
Toggle Mute On/Off
7
Note:
LED illumination is still functioning when it's in mute, but there will be no warning alarms
Repeat same steps in #8 to turn beeper On/Off.
.
Enter Seconds
(10~99)
1
4
5
6
7
8
Keep the door open while programming to avoid being locked out accidentally.
The lock contains one factory-preset user code but can be programmed to
store up to a total of six additional unique use codes.
Codes can be added and deleted at any time.
For first-time programming, use factory default programming code.
Add New User Code
Enter PC
1
Enter New UC
Note:
Up to 10 sets of user codes can be saved. User codes should be 4–10 digits in length.
Change Programming Code
Enter PC
4
Enter New PC
2
3
Note:
The lock can only be operated by key during that time.
Auto-locking and keypad locking functions will be invalid when user codes are deleted.
Enter PC
Enter PC
Enter PC
Enter PC
Enter PC
Enter PC
Trouble shooting
After installing the lockset and batteries,
the door can’t be locked and three short
beeps are emitted when you press the
Programming button.
The door-handing
identification process isn’t
yet complete.
Refer to step1.
When you are in the door-handing
identifying process, you get the red light
flashing three times, and three short
beeps.
Wrong door-handing or
change of the door-handing
in the memory.
Press the R button to restore the system
to factory default setting and re-execute
door-handing identifying process
(
step 1)
Refer to
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
(1) The depth of the latch
bolt hole is insufficient.
(2) The latch bolt is not
aimed at the opening
of the strike.
Although the electronic deadbolt has
been functioning normally, the latch bolt
suddenly locks up, and the turnpiece
inside can’t be rotated, not even with a
key.
While the door is locked, you hear the
latch bolt coming out when you press the
Gatehouse to lock the door; however,
three short beeps are emitted.
Conversely, while the door is open, no
beeps are emitted when locking the
latch bolt.
First, take out one battery, then press
any button on the front panel for electric
discharge, and put the battery back in.
The latch bolt will automatically
re-detect its position.
Note: If the latch gets stuck frequently,
please check and fix the alignment of
the deadbolt latch
&
strike plate.
(1) Dig the latch bolt hole for the strike
(2) Adjust the strike to the appropriate
position.
deeper.
The minimum depth is 1" (2.5 cm).
You’ve installed the lockset and batteries,
but you still get no response when you
press any button.
Batteries were installed
incorrectly.
Check to see if the battery polarities
have been reversed or if the battery is
dead.
If so, re-install or change the battery.
If not, please check to see if the cable is
properly connected.
Low battery.
Replace with new alkaline batteries.
Although you succeeded in the first
execution of the door-handing identifying
process, the latch still doesn’t work.
(i.e. You can feel the motor attempting to
run, but the latch bolt is stuck, and the
turnpiece can’t be rotated.)
The door can be locked normally, but
when you try to unlock it, you hear three
short beeps and the lock won't unlock
when you enter the user code and press
the programming button.
Unlock the door with the key and
re-program the unit.
If the problem persists, call our customer
service department.
The deadbolt latch is stuck
due to a warped door or
misaligned door.
The sensor did not sense
position.
R
2
3
4
5
6
7
8
9
0
1
3 Long Beeps
ELECTRONIC DEADBOLT
Enable/Disable All User Codes
Note:
The lock can only be operated by key during the time.
Repeat the steps to enable the user codes again.
Auto-locking and keypad locking functions will be invalid when user codes are disabled.
9
8
Enter PC
Create a One-Time User Code 4–10 Digits Long
10
Enter PC
9
Enter
One Time
Code
Note:
The one-time user code will automatically cancel after it is used one time.
It’s recommended to change the default programming code and
default user code right after your install the lock.
!
FGS-
2
PL1-
