background image

Installation – 

Mounting Height & Clearance

6

DUCTING

A minimum of 6” round duct must be used to 

maintain maximum air flow efficiency.

Always use rigid type metal ducts only. Flexible 

ducts could restrict air flow by up to 50%.

Use calculation worksheet to compute total duct 

work (Page 5).

ALWAYS, when possible, reduce the number of 

transitions and turns. If a long duct run is required, 

increase duct size from 6” to 7” or 8”.

If turns or transitions are required: Install as far 

away from duct opening and as far apart between 

the two transitions as possible.

Minimum mount height between range top to hood 

bottom should be no less than 24”.

Maximum mount height should be no higher than 

34”.

It is important to install the hood at the proper 

mounting height. Hoods mounted too low could 

result in heat damage and fire hazard; while hoods 

mounted too high will be hard to reach and will 

loose performance and efficiency.

If available, also refer to range manufacturer’s 

height clearance requirements and recommended 

hood mounting height above range. Always check 

your local codes for any differences.

Duct cover extension kit available for ceiling 

heights up to 12 feet. Turn to page 17 for part 

number and ordering information.

DAMAGE-SHIPMENT / INSTALLATION:

•  Please fully inspect unit for damage before 

installation.

•  If the unit is damaged in shipment, return the 

unit to the store in which it was bought for 

repair or replacement.

•  If the unit is damaged by the customer, repair 

or replacement is the responsibility of the 

customer.

•  If the unit is damaged by the installer (if other 

than the customer), repair of replacement must 

be made by arrangement between customer 

min.  A

min.  B

max. C

 

 

 

    

Standard  

Extension

Hood Heights  

 

Duct Cover  Duct Cove

r

            minimum ducted (A)  28” 

 

50 

1/2

 minimum recirculating (B)  32” 

 

50 

1/2

                          maximum (C)  39” 

 

80”

Ceiling Heights

           minimum ducted (D)  88” (7’ 4”) 

110 

1/2“

 (9’ 2 

1/2”

)

 minimum recirculating (E)  92” (7’ 8”) 

110 

1/2“

 (9’ 2 

1/2”

)

                          maximum (F)  109” (9’ 1“)        150” (12’ 6”)

36”

24” min.

34” max.

min.  D

min.  E

max. F

Содержание MH10836BS





















Отзывы: