Mircom BPS-602, Руководство по установке

Страница: 4 / 16

- 4 - BPS-602
Class A, Style Z Class B, Style W, X, Y, SW1 & SW2 Settings:
• For all Class B, Style W, X, Y, hookups SW1 & SW2 on the AL800LGK9E logic board must be open.
For all Class A, Style Z hookups SW1 & SW2 on the AL800LGK9E logic board must be closed.
Output Programming Selection Table:
Outputs must be programmed independently (OUT1 - OUT4)
Function
Switch Positions
Descriptions
ON OFF
Input to Output Follower
Mode
1 2, 3
Output follows signal it receives from the corresponding input
(i.e. FACP Sync module - maintains synchronization of
notification appliance circuit).
Temporal Code 3 Mode 3 1, 2
Enables Temporal Code 3 signal generation output.
This mode will accept a steady or a pulsing input.
Steady Mode 1, 2, 3 A steady output signal will be generated.
This mode will accept steady or pulsing input.
For the above modes Dip Switch 4 determines which Input controls
the corresponding output:
Switch 4 in the ON position causes output(s) to be controlled by Input 1.
Switch 4 in the OFF position causes output(s) to be controlled by Input 2.
Note: It is required to control visual notification appliances (strobes) via Input 1 (IN1)
and audible notification appliances (horns) via Input 2 (IN2). This allows audible
notification appliances (horns) to be silenced while visual notification appliances (strobes) continue to operate. The
FACP must be capable of a visual annunciation to the silencing status of the output or zone(s) to which the
BPS-602 (NAC Power Extender) is connected.
Sync Mode Selection Table:
Function
Switch Positions
Descriptions
ON OFF
Amseco Sync
Mode*
1, 3,
4
2
This mode is designed to work with the Amseco series of horns, strobes, and
horn/strobes to provide a means of synchronizing the Temporal-coded horns,
synchronizing the flash timing of the strobe, and silencing the horns of the horn/
strobe combination over a two-wire circuit while leaving strobes active.
Faraday
Sync Mode*
2, 4 1, 3
This mode is designed to work with the Faraday series of horns, strobes, and horn/
strobes to provide a means of synchronizing the Temporal-coded horns, synchroniz-
ing the flash timing of the strobe, and silencing the horns of the horn/strobe combi-
nation over a two-wire circuit while leaving strobes active.
Gentex
®
Sync Mode*
Gentex is a registered
trademark of Gentex Corporation.
1, 2,
3, 4
This mode is designed to work with the Gentex
®
series of horns, strobes, and horn/
strobes to provide a means of synchronizing the Temporal-coded horns, synchroniz-
ing the flash timing of the strobe, and silencing the horns of the horn/strobe combi-
nation over a two-wire circuit while leaving strobes active.
System Sensor
®
Sync Mode*
System Sensor is a registered
trademark of Honeywell.
1, 2, 4 3
This mode is designed to work with the System Sensor
®
series of horns, strobes,
and horn/strobes to provide a means of synchronizing the Temporal-coded horns,
synchronizing the one-second flash timing of the strobe, and silencing the horns of
the horn/strobe combination over a two-wire circuit while leaving strobes active.
CooperWheelock
®
Sync Mode*
CooperWheelock is a
registered trademark of
Cooper Wheelock.
2, 3, 4 1
This mode is designed to work with the CooperWheelock series of horns, strobes,
and horn/strobes to provide a means of synchronizing the Temporal-coded horns,
synchronizing the one-second flash timing of the strobe, and silencing the horns of
the horn/strobe combination over a two-wire circuit while leaving strobes active.
(AL800LGK9E Board)
Output Dip Switches
INPUT SELECT
TEMPORAL
STROBE SYNC
IN>OUT SYNC