Minuteman Port A Scrub 14 Скачать руководство пользователя

Страница: 12 / 48

Mount Squeegee (Initial Fitting)

Lift squeegee and hold it to the squeegee holders (3).

Mount squeegee (1) to the squeegee holder by means of screws (2) as

represented

Check the smooth running of the bottom sleeve at the squeegee

holders for perfect hinging.

Dismount Squeegee

Lift brush head of the Port A Scrub 14 in order to access the squeegee screws.

Remove both screws (2) as represented.

Pull squeegee to the bottom to remove it from the machine.

Change Sealing Strips

No tools are required for dismounting the sealing strips. Proceed as

follows:

Dismount squeegee (refer to paragraph “Dismount squeegee” ).

Unscrew knurled screw (1)

Remove support strip

Proceed to mounting of new sealing strip in reverse order.

Tighten the knurled screws (by hand) and from the centre towards the
outsides (slotted sealing strips point to the front, plain ones to the back)

Proceed as follows for cleaning the nozzle:

(I) Remove nozzle

Dismount brushes from the Port A Scrub 14 (see
“Dismount/Mount Brushes”).

Lift machine and lay down on its back as represented.

Turn the nozzle to the left

(II) Clean nozzle

Clean nozzle by compressed air or water

(III) Mount nozzle

After cleaning, insert nozzle by screwing clockwise

make sure that the nozzle slot is as the mounting direction of the brushes.

Upright machine

1.squeegee
2.squeegee screw
3.squeegee holder

1. Knurled screw
2. Support strip
3. Sealing strip

The rear sealing strip can be turned round if worn at the front edge.

NOZZLE

Tighten

Loosen

Clean nozzle

The nozzle clogs after some hours of operation. It thus

required to clean the nozzle at daily intervals before start of
operation.

Nozzle Slot

Squeegee

The Port A scrub 14 has been equipped with a squeegee of 450 mm working width. The squeegees can be lifted-
out alternately

Check the squeegee for collected foreign particles and

Содержание Port A Scrub 14

















































Результаты поиска

Содержание Port A Scrub 14

Отзывы:

Похожие инструкции для Port A Scrub 14

Бренды по названию

Популярные бренды

Minuteman Port A Scrub 14, Инструкция по эксплуатации

Результаты поиска

Содержание Port A Scrub 14

Отзывы:

Похожие инструкции для Port A Scrub 14

Бренды по названию

Популярные бренды