MINOURA BikeTower 20D Скачать руководство пользователя страница 2

Страница: 2 / 6

- 2 -

How To Setup

Measurement

→

Temporally Setting

→

Adjusting Length

→

Setting

→

Check

→

Fix

○ ×

｝

Loosen

The Upper

and Lower

Pillars come

separated.

The Center

Pillar is

retraced inside

the Upper

Pillar.

Loosen the

M6x15 bolt

and two M6x20

bolts of the

upper Pillar

Joint to extract

the Center

Pillar.

After

extracting,

tighten the bolts

temporally.

HINT

You should know the

Lower Pillar length is

1.2 meters.

Use this fact as a scale

to measure the ceiling

height from the floor.

For example, if the

ceiling is just twice of

the Lower Pillar, it's 2.4

meters.

The Center Pillar is

90cm long, and it

should be inserted into

both Upper and Lower

Pillars symmetric to

expect the maximum

durability of the total

pillar.

For example, if the

ceiling height is 2.4

meters, you should

set the Center Pillar is

25cm sunk in the Upper

Pillar (65cm remaining).

This will avoid the

troublesome re-setting

of the pillar length after

setting up the stand.

Loosen the

M6x15 bolt of

the Lock Plates,

move them to the

mid zone of the

Center Pillar and

hold.

Loosen both

M6x15 and

M6x20 bolts to

move the lower

Pillar Joint

upward.

Extract

Insert the Center

Pillar into the

Lower Pillar.

Make sure the

Lower Pillar

comes until the

end of the Pillar

Joint plastic

sleeve.

You will adjust

the total pillar

length at the

Upper Pillar, so

you tighten the

M6x20 bolts of

the lower Pillar

Joint firmly

(tightening

torque =

8 N.m

Loosen

Move

The Lower Pillar must be fully

inserted into the Pillar Joint.

If some clearance remains,

the pillar may be too short

and could fall down, causing

a serious accident.

8 N.m

Tighten

MAX Decal

In anticipation

of the stand

being installed

on a stable and

even surface,

have the the

Center and

Lower Pillars

matching in

length for the

time being.

(see Fig. E)

The MAX

decals MUST

be hidden from

view.

After this

point there

is no need

to touch the

Lower Pillar

any longer.

Assembly

is now

complete

and you will

move on to

adjusting the

pillar length

to match the

height of

your ceiling.

Required Tool :

5mm Hex Wrench

(Fig. A)

(Fig. B)

(Fig. C)

(Fig. D)

(Fig. E)

(Fig. F)

Содержание BikeTower 20D







Результаты поиска

Содержание BikeTower 20D

Отзывы:

Бренды по названию

Популярные бренды

MINOURA BikeTower 20D, Инструкция по эксплуатации

Результаты поиска

Содержание BikeTower 20D

Отзывы:

Бренды по названию

Популярные бренды