MINN KOTA Latch & Door Скачать руководство пользователя страница 5

MOUNT INSTALLATION

INSTALLATION OF THE BOW-MOUNT

We recommend that you have another person help with this procedure.

1.  For installation,

 DO NOT REMOVE THE SHAFT/MOTOR FROM THE BOWGUARD

The Bowguard spring is 

under tension and must always remain secured. 

Latch and Door models can be removed from the mount if needed.

2.  Place the mount, with the motor in the fully stowed (fl at) position, on the deck of the

boat:

•  The motor should be mounted as close to the centerline of the boat as possible

when it is deployed (see illustration).

•  Make sure bow area under the chosen location is clear and unobstructed for

drilling.

•  Make sure the motor rest is positioned far enough beyond the edge of the 

boat. The motor, as it is lowered into the water or raised into the boat, must not
encounter any obstructions

3.  Once in position, determine which bolt pattern to use (see below), mark at least 4 

of the holes (2 on each side) in the bow plate and drill through with a 9/32” drill bit.
Either pattern may be used when installing the motor.

 -  Pattern 1:  Minn Kota 3” bolt pattern standard motors.

 - Pattern 2:  Alternate 4” bolt pattern commonly used.

4.  Install hold down strap between the motor and deck of boat between second and third set of mounting holes.

5.  Mount the plate to the bow through the drilled holes using the provided (1/4-20 x 3-1/2”) bolts, nuts and washers.

NOTE:

 If possible, secure all sets of mounting bolts, nuts and washers.

6.  Install the bow mount stabilizer (if included). See next section for installation instructions.

Hold Down Strap

1

2

Содержание Latch & Door




















Отзывы: