background image

 

 
miniDSP Ltd – Hong Kong / Email : 

[email protected]

 / Features and Specifications are subject to change without prior notice 

P 14 

4.3.6

 

Compressor /Limiter 

 

4.3.7

 

Master volume control 

The master volume allows control of all 10 outputs channels ( digital) of the miniDSP unit. It is enabled from the front panel 
unit (VOL-FP panel) and requires a small configuration from the software to be enabled.  Please make sure to select the “IR mode” to 
make sure your unit is correctly configured.  

 

 

 

4.4

 

Load/Save/Restore a configuration 

4.4.1

 

Load configuration: 

 Use this feature to load a previously saved configuration. The file must be as .xml format and previously saved from this plug-in. For 
complexity reasons, inter-plug-in compatibility is not available. 
 

4.4.2

 

Save Current Configuration 

 Use this feature to save your audio settings configuration. The following dialog box allows you to save the file anywhere on your PC as 
a .xml format. Only the current selected preset memory is saved.   

 

4.4.3

 

Restore Factory default 

Use this feature to restore the board back to factory default. Warning that all configurations will be restored back to default from this 
action.  

 

4.4.4

 

Restore Factory default 

Use this feature to restore the board back to factory default. Warning that settings of all four configurations will be blanked back to 
default.  
 

4.5

 

Firmware upgrade 

In order to enable some new features, the miniDSP may require to be flashed with a new firmware. All the required tools 
and firmware files are already included in the in the installation folder of the plug-in. So the first step to make sure you 
have everything you need is to install the new plug-in by logging to the UserDownload section. Note that firmware 
upgrade tools is Windows only at this point of time. A mac tool is in the works.  
 

Comp/ Limiter metering 

shows real time amount of 

attenuation by comp/limiter 

Bypass Comp/ Limiter 

Comp/ Limiter chart 

Typical Comp/Limiter settings 

A compressor/Limiter allows dynamic range compression of the signal to prevent damage of your speakers. Extensive information is 

available online

 on the use of compressor/limiter. Please take the time to familiarize yourself with such processing block before 

using it.  
 

Содержание 4x10

















Отзывы: