Mini-Circuits PWR Series Скачать руководство пользователя страница 33

Страница: 33 / 44

AN-48-003 Rev. H (Jun 09, 2022) This document and its contents are the property of Mini-Circuits ECO-013719 Page 33 of 44

3.8

Firmware Update (Supported models only)

3.8.1

All power sensors are shipped with

the latest available firmware and an

update is usually not required. Mini-Circuits occasionally makes firmware update files

available as a courtesy to add additional features or correct known issues. Please contact

[email protected]

for details.

3.8.2

Models supporting firmware upgrade:

The following firmware upgrade instructions apply to all power sensor controller versions, but

with some visual differences (for PWR-40PW-RC) highlighted below.

Check the list below for models which support firmware upgrade:

- PWR-8GHS-RC

- PWR-6RMS-RC

- PWR-6LRMS-RC

- PWR-6LGHS

- PWR-8P-RC

- PWR-40PW-RC

3.8.3

The smart RF Power Meter GUI

must be started in USB control (See section

3.1

) to allow Firmware upgrade. When in USB control, you will note an

(fw)

indicator over the

serial number field in the power sensor’s main screen.

A power interruption, to either the computer or the power sensor while the firmware is

being updated may cause the firmware to be corrupted. It is therefore recommended to

only update the firmware while the computer is connected to an Uninterruptible Power

Supply (UPS).

3.8.4

Click on the ‘(fw)’ indicator,

this will cause the firmware - info window to open

(See

Fig. 3.8.4

). The ‘Firmware’ listed is the version of the firmware installed in your smart

power meter. Click on “Update Firmware” to select a new firmware version to install or click

‘Exit’ to close the firmware – info window.

Figure 3.8.4:

Firmware Information Window

Figure 3.8.3:

Firmware indicator on main screen

CAUTION

Содержание PWR Series













































Результаты поиска

Содержание PWR Series

Отзывы:

Бренды по названию

Популярные бренды

Mini-Circuits PWR Series, Руководство пользователя

Результаты поиска

Содержание PWR Series

Отзывы:

Бренды по названию

Популярные бренды