background image

2.

list of parts

p6

3. List of Parts

The box in which the Sovereign GT is shipped should contain the following items. 
Please check that all of these items are in the box:

- See note

• Control Box 
• 10" or 8” Round Tornado coil (inc. skid plate attached) 
• 2-Piece Shaft Assembly (inc. Fiberglass lower shaft) 
• Black Aluminium Armrest (inc. nuts & bolts) (2 part) 
• Arm Rest Neoprene Cover 
• Arm Rest Strap (2 part) 
• Rear Control Box Bracket 
• Battery Pack 
• Velcro

TM

Straps (2 pair) 

• Teardrop Washers (2) 
• Nylon Nuts and Bolts 
• Warranty Card 
• Instruction Manual 

Note: There may be variations to the items included in different countries so if you believe there may
be something missing, check with your dealer/supplier that it is standard issue.

4. Accessories

The following accessories are available to further improve your machine.

• Digital Target Identification Meter  
• Alkaline Battery Holder ( holds 8 x ‘AA’ Batteries)
• NiMH rechargeable battery
• Mains Charger (240v/230v or 110v) 
• 12V NiMH Vehicle Charger
• Headphones
• Hipmount Bag with Raincoat Protective Cover for Control Box
• Meter Protective Cover & hipmount Bag
• Padded Detector Transport Bag
• Minelab Padded Sleeveless Jacket
• Blue Minelab Polo Shirt
• Blue Minelab Cap

For further information on these and other Minelab products call your nearest
Authorised Minelab dealer.

www.minelab.com

5.

assembling the detector

www.minelab.com

p7

5. Assembling the Detector

Please follow these instructions to assemble the Sovereign GT. Refer to the 
drawings to identify parts and how they are positioned. Please contact your
Minelab dealer for further instructions should any difficulties arise.

5.

1.

Lower Shaft Assembly

a)

Remove the tape on the lower fiberglass tube (3) that is 

holding the black teardrop washers (12) in place.

Note:

Ensure the washers do not fall out after removing the tape.

b)

Remove the black nylon wing nut (11), and bolt (10) from 

the coil (1).

c)

With the teardrop washers in place, push the lower tube (3)

into the coil bracket so that the holes line up.

Note:

Ensure that the black nylon spring clip near the top of 

the fibreglass tube is pointing toward the rear of the coil.

d)

Push the black nylon bolt (10) through the holes in the 

bracket on the coil from the cable entry side and tighten 
the wing nut (11) by hand.

5.

2.

Armrest/Upper Straight Shaft Assembly

Note:

In some countries the Sovereign GT is issued with an S-bend upper shaft and in 

other countries it will have a straight shaft.

a)

Slide the handle (5) onto the upper end of the upper shaft (4)

and push it on about a foot.

b)

Place the two arm rest halves (6) on either side of the upper 

shaft (4) and ensure that the bolt holes are aligned.

c)

Slide the nylon bolts (10) through the bolt holes 

and screw the nylon wing nuts (11) onto the bolts 
with a couple of turns (do not tighten).

d)

Slide the plastic control box bracket (9) into

the runners of the arm rest (6) & tighten the nylon
wing nuts by hand.

e)

Attach the arm rest straps (8) using the

press studs on both sides of the arm rest.

f)

Push the arm rest straps through the slots 

in the arm rest cover (7) and push the cover
over the arm rest.

g)

Position your arm into the arm rest and slide the

handle (5) along the shaft into a comfortable position.
Tighten the two screws in the base of the handle with a 
small screwdriver.

If your detector is supplied with the S-bend shaft, assembly will be identical except that you
will not have to assemble the separate handle

Figure 1

- The coil and

lower shaft assembly

Figure 2

- Armrest/upper

shaft assembly

Содержание Sovereign GT




















Отзывы: