Minebea Intec CAS1 Скачать руководство пользователя страница 94

Страница: 94 / 160

7.3 Internal Calibration/Adjustment for CAS… Models

System Requirements
-

"Internal Calibration" must be set in the Setup:
Menu [SETUP] - [WP-1] - [INTERN.] - [PARAM.1] - [CAL./ADJ] - [CAL.INT.] (1.9.4) (see

chapter

6.3.1.1.1

The scale housing has a built-in motorized calibration weight.

Example:

Internal calibration and then adjustment (see chapter

7.3.1

7.3.1

Example: Internal calibration

Internal calibration and then adjustment (weighing parameters: factory settings for CAS…

models)

(e.g., when adjustment prompt lashes WP). [CAL.INT.] is displayed for two seconds.

--------------------

Typ CAW1P1-3DC-L
Ser.no. 12345678
Vers. C1 111.031112
BVers. 01-62-02
Ser.no. A 12345678
--------------------
Ext. Kalibrieren
Soll + 10000 g
Diff. + 1 g
Ext. Justieren
Diff. + 0 g
--------------------

Name:

--------------------

1. Waage nullstellen with

key.

2. Startcalibration with

key.

The internal calibration weight is loaded automatically.

Combics 1 Series Complete Scales Models CAW1P, CAW1S, CAS1

7 Operating

EN-92

Minebea Intec

Содержание CAS1

































































































































































Результаты поиска

Содержание CAS1

Отзывы:

Minebea Intec CAS1, Руководство по эксплуатации, Страница: 94 / 160

Результаты поиска

Содержание CAS1

Отзывы: