PROBLEM
CAUSE
SOLUTION
1) Charge level of vehicle battery has dropped below
useable level.
1) Remove battery from vehicle and charge with the
recommended charger. Always follow proper safety
procedures when charging a battery.
2) Inputs (sensors) or Outputs (servos, ESC, etc) are
wired improperly.
2) Check that each device connected to the Arduino
Sensor Shield is plugged in properly. Both in polarity
and into the proper port the program states.
3) Sensor is malfunctioning.
2) Check #2, Connect Arduino to computer using
USB cable, run the calibration program for each
sensor on the vehicle. If the sensor value is not
present, uncharacteristic or erratic the sensor may
need to be replaced.
1) The Arduino is not connected to the computer.
1) Connect the supplied USB cable and try again.
2) The proper serial port was not selected in the
Arduino Program.
2) Disconnect, re-connect the USB Cable then go to
Tools > Serial Port then select the Arduino Uno.
1) The Ping))) sensor is not wired properly.
1) Check the wiring polarity guide for proper
installation.
2) The Ping))) sensor in not connected to the proper
port.
2) Check that the sensor is plugged into the port
stated in the code.
1) The QTI sensor is not wired properly.
1) Check the wiring polarity guide for proper
installation.
2) The QTI sensor in not connected to the proper
port.
2) Check that the sensor is plugged into the port
stated in the code.
1) One of the connections to the Sensor Shield is
shorted.
1) Check that each device connected to the Arduino
Sensor Shield is plugged in properly. Both in polarity
and into the proper port the program states. If the
problem persists disconnect one sensor at a time till
the faulty connection (sensor, servo, ESC etc.) is
found, then replace.
2) No power source is connected to the Arduino
2) Check to make sure that it is either plugged into
your computer with the USB cable or that you are
using a charged battery and the ESC cable is
properly connected.
http://arduino.cc/en/Guide/Troubleshooting
Vehicle is not behaving as programmed.
Serial port "COM_" not found.
Light on Ping))) sensor is not cycling.
QTI sensors not detecting line.
Power light on Arduino Sensor Shield doesn't turn on
when ESC is powered on.
ARDUINO TROUBLESHOOTING GUIDE
- 26 -
Содержание EMC-ARD1-001
