Mindray BeneFusion SP3 Скачать руководство пользователя

Страница: 13 / 80

2-1

Overview

2.1 Product Introduction

2.1.1 Structure, Composition and Performance

The syringe pump product is mainly composed of a syringe pump main unit,

fastening clips and infusion monitoring management system (BeneFusion DS3).

The speed of the stepper motor is precisely controlled to drive the screw operate at

a set speed, thus controlling the flow of liquid injected into the patient's body by the

syringe. This product can be used for clinically accurate infusion of the drug to the

patient, and all of its components are suitable for the patient environment. The

syringe pump main unit can be equipped with a wireless module. The software

optional functions include speed mode, time mode, weight mode, drug library,

historical records, and Anti-bolus.

The application part of this equipment is a syringe. Since some parts and functions

are optional, the syringe pump you purchased may not have some parts and their

corresponding functions.

2.2 Main Unit

2.2.1 Front View

1. Alarm lamp

The alarm lamp indicates the alarm priority in different colors and flashing

frequencies.

Содержание BeneFusion SP3

















































































Результаты поиска

Содержание BeneFusion SP3

Отзывы:

Похожие инструкции для BeneFusion SP3

Бренды по названию

Популярные бренды

Mindray BeneFusion SP3, Руководство по обслуживанию

Результаты поиска

Содержание BeneFusion SP3

Отзывы:

Похожие инструкции для BeneFusion SP3

Бренды по названию

Популярные бренды