Mindray Accutorr V Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 130

background image

Accutorr V Operating Instructions

0070-10-0699-02

v

Foreword

Introduction

Foreword

These operating instructions are intended to provide information for the proper operation of
the Mindray DS USA, Inc.

/Shenzhen Mindray Bio-Medical Electronics Co., Ltd

Accutorr V.

The Accutorr V configurations are:

•

Accutorr V with Nellcor

®

Pulse Oximetry

—

includes NIBP, Nellcor SpO

2,

a Trend Display, and Recorder

•

Accutorr V with Nellcor

®

Pulse Oximetry and SmarTemp™

—

includes NIBP, Nellcor SpO

2,

SmarTemp, a Trend Display, and Recorder

•

Accutorr V with Masimo SET

®

Pulse Oximetry

—

includes NIBP, Masimo SpO

2,

a Trend Display, and Recorder

•

Accutorr V with Masimo SET

®

Pulse Oximetry and SmarTemp™

—

includes NIBP, Masimo SpO

2,

SmarTemp, a Trend Display, and Recorder

•

Accutorr V with DPM Pulse Oximetry

—

includes NIBP, DPM SpO

2,

a Liquid Crystal Display (LCD), and Recorder

•

Accutorr V with DPM Pulse Oximetry and SmarTemp™

—

includes NIBP, DPM SpO

2,

SmarTemp, a Liquid Crystal Display (LCD), and Recorder

•

Accutorr V with DPM

NIBP and SmarTemp™

—

includes NIBP, SmarTemp, a Trend Display, and Recorder

•

Accutorr V with DPM

NIBP only

—

includes NIBP, a Trend Display, and Recorder

All Accutorr V configurations can be upgraded with a barcode scanner.

In this manual, when a described feature refers to a particular Accutorr V configuration, it
will be noted. When the name Accutorr V is used, it refers to all configurations.

General knowledge of monitoring and an understanding of the features and functions of the
Accutorr V are prerequisites for its proper use.

DO NOT OPERATE THIS UNIT BEFORE READING ALL INSTRUCTIONS.

Refer to the Accutorr V Service Manual: P/N 0070-00-0702 for information for servicing this
instrument. For additional information or assistance, contact an authorized representative.

U.S. Federal Law restricts this device to sale by or on the order of a physician or other
practitioner licensed by state law to use or order the use of this device.

Mindray maintains a policy of continual product improvement and reserves the

right to

change materials and specifications without notice.

Masimo Patents: This device (MASIMO SpO

2

Module) is covered under one or more of the

following U.S. Patents 5,758,644, 5,823,950, 6,011,986, 6,157,850, 6,263,222,
6,501,975, and other applicable patents listed at: www.masimo.com/patents.htm.
Possession or purchase of this device does not convey any express or implied license to use
the device with replacement parts which would, alone, or in combination with this device,
fall within the scope of one or more of the patents relating to this device.

«
...
6
7
8
9
10
...
»

Содержание Accutorr V



































































































































Отзывы:

Нет отзывов

Похожие инструкции для Accutorr V

Бренд: GALBIATI Страницы: 20

Бренд: Rational Страницы: 60

Бренд: TANACOM Страницы: 27

Бренд: iBACheck Страницы: 2

Бренд: Teac Страницы: 76

Бренд: Teac Страницы: 3

Бренд: Teac Страницы: 50

Бренд: Teagle Страницы: 2

Бренд: TEC Страницы: 6

Бренд: U Technology Страницы: 6

Бренд: Yamaha Страницы: 139

Бренд: Yamaha Страницы: 19

Бренд: Yamaha Страницы: 32

Бренд: K-SPORT Страницы: 5

Бренд: Brillion Страницы: 56

Бренд: HEINE Страницы: 4

Бренд: Harken Industrial Страницы: 6

Бренд: König Electronic Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды