Mindray Accutorr V Скачать руководство пользователя страница 28

Страница: 28 / 130

Accutorr V Operating Instructions

0070-10-0699-02

2 - 7

Controls and Indicators

Rear Panel

2.3

Rear Panel

FIGURE 2-2

Accutorr V — Rear Panel

35. TEMP probe sheath

Holds the temperature probe when not in use.

36. TEMP probe covers

Holds the temperature probe covers for easy access.

37. TEMP probe connector

Used to attach a temperature probe to the Accutorr V.

NOTE:

The Temperature Module is an optional kit.

38. RS-232 connector

Used to attach a bar code scanner or DIAP.

NOTE:

When the RS-232 connector is used for DIAP, barcode power
must be set to OFF. Refer to Section 3.16.1 for turning
BARCODE POWER to OFF.

39. Nurse call connector

Provides compatible communication from the Accutorr V to the hospital’s nurse call system.

NOTE:

All equipment attached to the communications ports on the
Accutorr V must meet the requirements as specified in
EN 60601-1-1.

Содержание Accutorr V



































































































































Результаты поиска

Содержание Accutorr V

Отзывы:

Похожие инструкции для Accutorr V

Бренды по названию

Популярные бренды

Mindray Accutorr V, Руководство по эксплуатации

Результаты поиска

Содержание Accutorr V

Отзывы:

Похожие инструкции для Accutorr V

Бренды по названию

Популярные бренды