MIMAKI Tx500-1800B Скачать руководство пользователя страница 10

10

4. Periodically care (once in a week or two weeks)

(1) Replacing the carriage filter

Replace it once in a week or two weeks.

1

Move the carriage.

• Refer to the Step 1 to 4 of Chapter 4 “Cleaning the Wiper and

Cap” of the user’s manual to perform the operation.

2

Remove the carriage filter cover at the left and 
right of the carriage.

• Remove the carriage filter cover of right and left of the

carriage.

• Pinch the claw attached to the upper part of the carriage filter

cover and pull it to the front.

3

Remove the used carriage filter cover.

4

Mount a new carriage filter (SPA-0189).

• Insert the holes of right and left of the carriage filter into the

convex part of the carriage.

5

Return the carriage filter cover to the original 
status.

6

When replacement has been completed, press the 

 key.

7

Close the right maintenance cover and press the 

 key.

• The carriage filter is located at right and left of the 

carriage.
Replace both filters at the same time.

Carriage

Claw

Carriage filter cover

Carriage 

filter

new carriage filter

C l o s e a c o v e r

COMP L E T ED

[ ENT ]

Содержание Tx500-1800B

























Отзывы: