background image

13

13. Notes for working environment

Performing frequency of the print setting or maintenance is greatly influenced by the printing environment or 
the condition of the media used. Use this machine with a full understanding of the followings.

Working environment

Consideration

In the gritty and dusty place

To keep the nozzle face clean, set to wipe periodically every time it 
prints about 1500 mm. (Operation Manual Chapter 4 "Cleaning noz-
zle face automatically”)

Change the setting of periodic wiping depending on the amount of 
dust.

When the head gap is set wide 
because fibers stick out of media

UV light can expose the nozzle when there is a lot of scattered mist. 
Raise the refreshing level for drawing (Operation Manual Chapter 3 
"Other useful settings"), and set the periodic wiping ( Operation 
Manual Chapter 4 "Cleaning nozzle face automatically").

Increase performing frequency of every maintenance.

When the media that reflects UV 
light well is used such as glasses 
or glazed metal

When there is an infrequently-
used ink (print head)

An infrequently-used print head can be unstable to discharge ink 
comparing with the other print heads. Raise the refreshing level for 
drawing (Operation Manual Chapter 3 "Other useful settings") to 
raise the usage rate of the head.

When printing on the media on 
which static can be charged

Put humidifiers on to avoid charge. Static may collect mist or dust 
around the printing area or the head. To print continuously for a long 
time, set the periodic wiping. (Operation Manual Chapter 4 "Clean-
ing nozzle face automatically")

When printing in a dry place 
(such as in winter)

When printing on a markedly 
uneven media (or object)

To keep the head gap the same, set extra media outside the suction 
area where a printing media is set. Leaving the head that has been 
degraded by reflected light may cause failure that needs replacing of 
the head.

Содержание JFX500-2131

















Отзывы:

Похожие инструкции для JFX500-2131