Dear Customer,
Thank you for choosing a Milwaukee Instruments
product. This manual will provide you with the necessary
information for the correct use of the instrument. Please
read it carefully before using the meter.
SPECIFICATIONS
Range
0.00 to 2.50 mg/L PO
4
Resolution
0.01 mg/L
Precision
±0.07 mg/L @ 1.00 mg/L
Light Source
Tungsten lamp
Light Detector
Silicon Photocell and 610 nm narrow
band interference filter
Method
Adaptation of ascorbic acid method
Environment
0 to 50 °C (32 to 122 °F)
100% RH max
Battery Type
9 volt (1 pc)
Auto-Shut off
After 10’ of non-use
Dimensions
192 x 104 x 52 mm
(7.5 x 4.1 x 2”)
Weight
380 g
MEASUREMENT PROCEDURE
1. Turn the meter on by pressing ON/OFF.
2. When the LCD displays “- - -”, the
meter is ready.
3. Fill the cuvet with 10 mL of sample, up
to the mark, and replace the cap.
4. Place the cuvet into the holder and
ensure that the notch on the cap is
positioned securely into the groove.
5. Press ZERO and “SIP” will blink on the
display.
6. After a few seconds the display will
show “-0.0-”. The meter is now zeroed
and ready for measurement.
▶
7. Remove the cuvet. Open it.
8. Add the content of one packet of
MI512-0
reagent.
9. Reinsert the cuvet into the holder
and ensure that the notch on the
cap is positioned securely into the
groove.
10. Press and hold READ for 3 seconds
and the display will show the
countdown prior to the measurement.
Alternatively, wait for 3 minutes and
just press READ. In both cases “SIP”
will blink during measurement.
11. The instrument directly displays concentration in
mg/L of phosphate.
Interferences
y
Iron above 50 mg/L
y
Silica above 50 mg/L
y
Silicate above 10 mg/L
y
Copper above 10 mg/L
y
Hydrogen sulfide, arsenate, turbid sample and highly
buffered samples also interfere.
GUIDE TO DISPLAY CODES
This prompt appears for 1 second
each time the instrument is turned
on.
The dashes “- - -” indicates that the
meter is in a ready state and zeroing
can be performed.
Sampling In Progress. Flashing “SIP”
prompt appears each time the meter
is performing a measurement.
“-0.0-”, the meter is in a zeroed state
and measurement can be performed.
3’
The blinking “BAT” indicates that the
battery voltage is getting low and the
battery needs to be replaced.
“-bA-”, the battery is dead and must
be replaced. Once this indication
is displayed, the meter will lock up.
Change the battery and restart the
meter.
“Conf”, the meter has lost its
configuration. Contact your dealer
or the nearest Milwaukee Customer
Service Center.
ERROR MESSAGES
On zero reading
y
Blinking “-0.0-” indicates that the
zeroing procedure failed due to a
low signal-to-noise ratio. In this
case press ZERO again.
y
“no L”, the instrument can not
adjust the light level. Please check
that the sample does not contain
any debris.
y
“L Lo”, there is not enough light to
perform a measurement. Please
check the preparation of the zero
cuvet.
y
“L Hi”, there is too much light to
perform a measurement. Please
check the preparation of the zero
cuvet.
On sample reading
y
“-SA-”, there is too much light for
the sample measurement. Please
check if the right sample cuvet is
inserted.
y
“Inv”, the sample and the zero
cuvet are inverted.
y
“ZErO”, a zero reading was not
taken. Follow the instruction in
the measurement procedure for
zeroing the meter.
10 ml
▶
