4
OPERATION
WARNING
Always remove battery pack before
changing or removing accesso-
ries. Only use accessories speci
¿
cally recom-
mended for this tool. Others may be hazardous.
To reduce the risk of injury, always wear safety
goggles or glasses with side shields.
Fuel Gauge
To determine the amount of charge left in the bat-
tery, pull the trigger. The Fuel Gauge will light up for
2-3 seconds.
To signal the end of charge, 1 light on the fuel gauge
will
À
ash for 2-3 seconds.
Using the Drive Control
The drive control button is used
Speed Indicator
Drive
Control
Button
Auto Shut
O Mode
to adjust the rotation speed
(RPM) for the application.
To select the drive control
mode:
1. Pull and release the trigger
to turn on the tool. The cur-
rent indicator is lit.
2. Press the drive control but-
ton
to cycle through the
4 modes. When the desired
mode indicator is lit, begin
work.
* In Auto Shut O Mode, the tool
Mode
RPM
1
0-1200
2
0-1800
3
0-2700
0-2700
will drive forward at a reduced
RPM until the torque is
achieved. In reverse the tool
will operate at full RPM to re-
move fasteners at full torque.
Using the Control Switch
The control switch may be set to three positions:
forward, reverse and lock. Due to a lockout mecha-
nism, the control switch can only be adjusted when
the ON/OFF switch is not pressed. Always allow the
motor to come to a complete stop before using the
control switch.
Push for
Forward
r
o
f
h
s
u
P
Reverse
PUSH TO CENTRE TO LOCK
1. For
forward
(clockwise) rotation, push the control
switch in the direction shown. Check the direction
of rotation before use.
2. For
reverse
(counterclockwise) rotation, push the
control switch in the direction shown. Check the
direction of rotation before use.
3. To
lock
the trigger, push the control switch to the
center position. The trigger will not work when the
control switch is in the locked position.
Always remove the battery pack before performing
maintenance, changing accessories, storing the
tool and any time the tool is not in use.
1.
2.
the anvil.
3. To remove the accessory, pull the accessory o
(Cat. No. M12 FIW38 and M12 FIWF12)
Use only the appropriate size Square Drive Sockets.
To attach a socket, align the accessory with the
anvil and push it
¿
rmly over the retaining ring.
Attaching and Removing Accessories
3/8" and 1/2" Friction Ring
FUNCTIONAL DESCRIPTION
%HOWFOLS
&RQWURO
switch
+DQGOH
7ULJJHU
/('
)ULFWLRQULQJ
&DW
1R
0),:
9
1
2
4
3
5
7
6
0RGHGULYHFRQWURO
)ULFWLRQULQJ
&DW1R
0
),:)
6TXDUHGULYH
with
pin detent
&DW1R
0),:3
&DW1R
0),:
1/2" Pin Detent
&DW1R
0),:3
8VHRQO\WKHDSSURSULDWHVL]H6TXDUH'ULYH6RFNHWV
7RDWWDFKDVRFNHWDOLJQWKHKROHLQWKHDFFHVVRU\
ZLWKWKHGHWHQWSLQRQWROGWKHGHWHQW
SLQ LQ ZKLOH SXVKLQJ WKH VRFNHW RQWR WKH DQYLO
The detent pin will snap into place in the hole to
VHFXUHWKHVRFNHW
7RUHPRYHWKHVRFNHWLQVHUWDQDLORURWKHUWKLQ
REMHFW LQWR WKH KROH LQ WKH DFFHVVRU\ DQG SUHVV
LQWKHGHWHQWSLQ3XOOWKHDFFHVVRU\RႇWKHDQYLO
