background image

 

MPS Doc: M359_USER_MANUAL  REV G           January 17, 2010                                     Page 14 of 30

 

disconnected from the UPS input and the M359 is forced to operate from the internal 

battery (thus simulating an AC input failure).   In this mode, the INPUT FAIL red LED 

(17) should be on, the ON BATT yellow LED (16) should blink, the OUTPUT OK green 

LED (21) should remain on, and the Bar-graphs should indicate the Load and Battery 

charge level. 

 

5.3. Local Control (Using the Front Panel switches). 

 

If the M359 is controlled from its front panel switches, the remote ON/OFF switch should be 

in the On position and the remote UPS/BY-PASS selector in the UPS position. (If the Remote 

Switches function is not used, the mating connector of J4, with the jumpers described in 

Paragraph 5.1 above, should be installed on J4).  Please note that the M359 will turn On only 

if AC Input is available. The M359 will remain On (using Battery power) if AC input fails, but it 

will not start on Battery power alone.   

 

5.3.1. 

PWR ON/OFF Switch (2). 

 

When in the Off position (down) this switch disconnects both Input and Output of the 

M359 and turns off all functions (regardless off anything else).  When On, it enables the 

M359. The actual Operation Mode (UPS, By-Pass or Test) will depend on the setting of 

the other switches and controls.  In order to turn-on the M359 both the PWR ON/OFF 

Switch and the INPUT Switch must be in the upper position (and AC Input must be 

available). 

Once the M359 is On

, all Modes are accessible and depend only on the 

setting of the INPUT and OUTPUT switches (the exact sequence is not important).   

 

5.3.2. 

INPUT UPS/BY-PASS Switch (7). 

 

When this switch is in the By-Pass position (down), it disconnects the AC Power from 

the UPS input and the UPS (if already on and running) will continue to operate on 

Battery power. This state is useful as a 

Test Mode

 for the UPS functionality.   If 

both 

Input and Output

 UPS/BY-PASS switches are in the By-Pass position (down) and the 

PWR ON/OFF switch (2) is On (up), the M359 will be in the By-Pass mode.  In this 

mode AC power is routed (by-passed, internal to the M359) from the Input connector J1 

to the Output connector J2, via the isolation transformer and passive filters and all UPS 

functions are disabled.  

 

5.3.3. 

OUTPUT UPS/BY-PASS Switch (8). 

 

When this switch is in the BY-PASS position (down), it disconnects the UPS AC Output 

from the Output connector J2.  The UPS will be in the Stand-by mode, AC Output will be 

off, but the communication ports, the front panel display and the Battery Charger will 

remain active.  This state is useful if the battery needs charging but the presence of AC 

power on the output connector J2 is undesired.  If both the INPUT and OUTPUT 

UPS/BY-PASS switches are in the By-Pass position (down) and the PWR ON/OFF 

switch (2) is On (up), the M359 will be in the By-Pass mode (see 5.3.2 above). 

 

 

 

 

 

 

Содержание M359-1































Отзывы: