Milnor E-P Plus Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 92

Milnor E-P Plus Скачать руководство пользователя страница 49

Pellerin Milnor Corporation

43

pressure tube connection on the drain sump. Because the pressure
tube between the pressure transducer and the cylinder connects at
an elevation not exactly equal to the bottom of the cylinder, this
value allows for an accurate display of the water level. The unit of
this value is tenths of an inch, so a difference of 1.8 inches is en-
tered as 18. The maximum allowable value is 3 inches prior to
software version 97004, and 4.5 inches with software versions
97004 and later.

LEVEL 1 HEIGHT ?

6

This value is the depth of the water measured from the bottom of
the cylinder. This level will be used for any programmed bath step
commanding

Level 1

.

Level 1

must be achieved before steam is

allowed in any bath commanding steam.

The minimum level that can be configured for Level 1 is 5 inches
(13 centimeters) for V_J models. The minimum setting for H_J
models is 4 inches (10 centimeters). See

Table 9: Recommended

Water Levels, page 43

for recommended water levels.

LEVEL 2 HEIGHT ?

8

This value is the depth of the water measured from the bottom of
the cylinder. This level will be used for any programmed bath step
commanding

Level 2

.

The minimum valid value for this decision is equal to the value of
the

Level 1 Height

configured just before.

Use the same procedure to configure Levels 3 through 6 that you
used to configure Level 2. Keep in mind that each level must be
equal to or greater than the previous level. The maximum level
that can be configured is 15 inches (38 centimeters) for V_J mod-
els. The maximum setting for H_J models is 16 inches (40 centi-
meters). See

Table 9: Recommended Water Levels, page 43

recommended water levels.

Table 9.

Recommended Water Levels

Basket Dimension (from

model number)

Suggested Level 1 (Low Level) Suggested Level 6 (High Level)

Inches

Centimeters

Inches

Centimeters

30015

8

20

10

25

30022

8

20

10

25

36021

8

20

13

33

36026

8

20

13

33

42026

10

25

13

33

42032

10

25

13

33

Display or Action

Explanation

EXTRA WATER ?
0=NO, 1=YES

1

Select

1=Yes

only if this machine is equipped with an optional

third water valve. Configuring for extra water makes an addi-
tional programming decision available for bath steps, allowing
reuse of water drained from earlier baths, for example.

REUSE DRAIN ?
0=NO, 1=YES

1

Select

1=Yes

only if this machine is equipped with an optional

second drain valve. Configuring for reuse drain makes an

«
...
47
48
49
50
51
...
»

Содержание E-P Plus





























































































Отзывы:

Нет отзывов