Milnor E-P Plus Скачать руководство пользователя страница 23

Страница: 23 / 92

Pellerin Milnor Corporation

10. The

Manual button

(

) has no effect while a formula is running except when troubleshoot-

ing bath level errors. Pushing this button when the display says “Run Formula xx” initiates
manual mode, where the controls function as described in

2.1.2: Control Functions During

Manual Operation, page 17

. For troubleshooting bath level problems, hold the

Signal Can-

cel

Manual

, and

Next buttons

simultaneously to display the raw pressure data and the actual

number of inches detected by the bath level pressure transducer.

11. The

Terminate button

(

) cancels all remaining steps in any running formula and initiates

the shutdown procedure for the machine. Formulas ended in this manner cannot be resumed.

12. The

Door Unlock button

(

) unlocks the door. For safety, you must also hold this button to

open or close the optional power-assisted door or to jog or tilt the machine.

2.1.2

Control Functions During Manual Operation

BNCJHP01.R02 0000189820 C.2 A.5 1/2/20 1:16 PM Released

Manual operation is used primarily for troubleshooting the machine by activating outputs and
viewing inputs.

1. The

Start button

(

), when pressed while the

Manual button

is held down, activates the

selected menu function. Depress the

Start

and

Manual buttons

simultaneously to view the

software date code. For other manual menus, release the

Start button

when the menu appears

on the display.

2. The

Run/Program keyswitch

has no effect on how the manual mode operates. However, the

status of the switch ( or –) is displayed in field F in the

Test Inputs

menu.

3. The

Run Indicator light

is not activated during manual operation.

4. At the manual menu, the

Scroll Down button

(

) displays the available menu items in re-

verse numeric order.

5. In the manual menu, the display presents user prompts and selected information. The software

date code and machine configuration are displayed; inputs and outputs and their respective
statuses are shown in those modes. Other menu selections display DIP switch settings, as well
as temperature and level testing information.

6. The

Scroll Up button

(

) displays the next higher numbered mode in the manual menu.

For example, pressing this button once will scroll from the

Software Date Code

mode to the

Test Inputs

mode.

7. The

Next button

(

) has no function in manual mode.

8. The

Signal Cancel button

(

) has no function in manual mode.

9. The

Operator Signal light

does not operate when the controller is in manual mode.

10. Use the

Manual button

(

) to enter manual mode when the machine is idle.

11. The

Terminate button

(

) cancels manual mode and returns the controller to the normal

operation or programming mode, depending on the setting of the

Run/Program

keyswitch.

Any outputs that were manually actuated while in manual mode are turned off.

Programming

Содержание E-P Plus





























































































Результаты поиска

Содержание E-P Plus

Отзывы:

Milnor E-P Plus, Справочник, Страница: 23 / 92

Результаты поиска

Содержание E-P Plus

Отзывы: