Milnor E-P Plus Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 92

Milnor E-P Plus Скачать руководство пользователя страница 10

4

Pellerin Milnor Corporation

1.1.2.2

Steps that are Necessary When You Change Data

BNWCUD03.T02 0000189801 C.2 A.6 1/2/20 2:19 PM Released

1. Make a check of the machine configuration.

2. Write wash formulas.

3. Erase the formula accumulator data, if applicable. See the applicable sections in this manual

for instructions.

1.1.2.3

Data Accessibility

BNWCUD03.C04 0000189816 C.2 A.6 B.3 1/2/20 2:19 PM Released

The key switch must be in the

Program

position to change configuration and formula data. The

microprocessor controller changes the formula accumulator data while the machine operates.
Thus, the key switch can not prevent changes to the accumulator data. You can use the data as
given in

.

Table 2.

How to Read and Change Data

Data Type

How to Change Data

Configuration Data

You can read and change data.

Formula Data

You can read, change, and erase data.

Accumulator Data

You can read and erase data.

1.1.2.4

Replace Incorrect Data

BNWCUD03.C05 0000189826 C.2 A.6 1/2/20 2:19 PM Released

If the microprocessor finds incorrect data, the display will show an error message, usually when
the machine first gets power. The error can prevent machine operation. The troubleshooting in-
structions tell about each error and how to repair it. Obey these instructions to make sure that in-
correct data is replaced with correct data. You can cause dangerous operation or damage to the
machine if you do not obey these instructions.

BNWUUO01 / 2018153A

BNWUUO01

0000181431

A.3

1/2/20 2:19 PM

Released

1.2

Determining Load Size

BNWUUO01.C01 0000181430 C.2 A.3 B.3 1/2/20 2:19 PM Released

You will not do damage to the machine with a large load if you follow these rules:

1. The goods are made of common cotton or synthetic materials.

2. The load can balance in the cylinder before the extract step.

3. The extract speed has not been increased above the designed maximum.

4. You do not program so many extract steps that you do damage to the motor.

For common goods, the size of the machine sets the quantity you can put in the machine.

These items determine the maximum load weight of soiled goods:

•

the volume of the machine's cylinder, and

•

the material and weight of the goods.

«
...
8
9
10
11
12
...
»

Содержание E-P Plus





























































































Отзывы:

Нет отзывов