Milnor 42044SR2 Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 161

background image

96

Pellerin Milnor Corporation

5 Frame, Pivots and Suspension

BNWVUM01 / 2020106

BNWVUM01

0000277899

B.2

2/5/21 9:25 AM

Released

Suspension Adjustments for Divided Cylinder
Machines

BNWVUM01.C01 0000277938 A.3 B.2 2/5/21 9:25 AM Released

The suspension system on Milnor

®

Hydro-cushion™ machines is adjusted and thoroughly tested

at the factory. It should not require subsequent adjustment unless the machine is distorted during
shipment or installation or unless some component of the system, such as a Hydro-cushion™ cyl-
inder is replaced.

There are two primary objectives when adjusting the suspension system on any Hydro-cushion™
machine model:

1. To position the shell in the proper location within the frame (hanging dimensions) to maxi-

mize freedom of movement of the shell and to insure proper draining, and

2. To adjust the length of up and down travel at each of the push-down locations (push down

travel) so that the shell will not be distorted (racked) when pushed down.

All Milnor

®

Hydro-cushion™ machines contain the following suspension system components:

1. Hydro-cushion™ cylinder—which suspend the shell and cylinder within the frame and pro-

vide vibration damping during extraction.

2. Pneumatic push down devices (air bags)—which when inflated, force the shell downward

where it is held against rigid pads during loading, unloading, washing, and draining.

3. Metal or rubber pads—some rigidly fixed to the shell and some rigidly fixed to the frame,

which come in contact when the shell is pushed down.

The actual configuration of these components varies from model to model.

How Shell Adjustments are Made

BNWVUM01.T01 0000278202 A.3 B.2 A.2 3/3/20 4:33 PM Released

Regardless of machine model, repositioning of the shell is always accomplished by adjusting the
nuts at the top of the upper Hydro-cushion™ shafts. To move the shell up or down at the location
of any Hydro-cushion™, see

Figure 37: Hydro-cushion™ Upper Shaft and Adjusting Nuts, page

and proceed as follows:

CAUTION:

These procedures should be accomplished with power to the machine

locked off.

1. Straighten the tongues on the keyed lock washer using pliers, screw driver, etc.

2. Loosen the lock nut (upper hex nut) and move it all the way up to the top of the shaft, but do

not remove it.

«
...
96
97
98
99
100
...
»

Содержание 42044SR2


































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 42044SR2

Бренд: Igloo Страницы: 1

Бренд: Rational Страницы: 112

Бренд: Zanussi Страницы: 24

Бренд: Haier Страницы: 8

Snack Heroes CP4600

Бренд: Sunbeam Страницы: 12

Бренд: NewAir Страницы: 14

Бренд: Zelmer Страницы: 52

Бренд: Zelmer Страницы: 54

Бренд: Ooni Страницы: 36

Pasta&Beyond PM-01

Бренд: Emeril Lagasse Страницы: 24

Бренд: EdgeStar Страницы: 19

Бренд: SANHOYA Страницы: 31

5-Blade Spiral Slicer

Бренд: Spiralizer Страницы: 8

Бренд: cecotec Страницы: 17

Бренд: cecotec Страницы: 29

Бренд: Hamilton Beach Страницы: 80

Бренд: Summit Страницы: 24

Бренд: Bellarom Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды