Miller OM-246 466B, Руководство пользователя

Страница: 73 / 76

OM-246 466 Page 69
Description
Part
No.
Dia.
Mkgs.
Item
No.
Figure 9-5. Front Panel Assembly (Fig 9-1 Item 14) (Continued)
Quantity
10 216966 Cover, Connector D-sub 9 pin Male w/Chain 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 213102 Choke, Common Mode w/Leads 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 210866 Terminal, pwr output black 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13 210477 Panel, Front 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14 219843 Label, Volt Sense 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15 207979 Box, Louver 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16 186621 Boot, Generic 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17 231056 Knob,Black Electroswitch 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18 212779 Nameplate, Front 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19 210865 Terminal, pwr output red 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20 210483 Bracket, lift eye 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21 210358 Bolt, eye shld thd stem .500 − 13 X 1.500 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
*Recommended Spare Parts.
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
Ordering Information For PCM, AIM And UIM Circuit Boards
The UIM, AIM and PCM boards must have compatible programs in order to communicate together and provide proper
system performance. If the program has been updated since the system was received, the original program revision
may not match the serial number of the PipePro 300 shown in Table 9-1. In order to provide the correct replacement
board, it is necessary to know the program revision for each of the boards in the PipePro 300.
Follow the procedure to Check Program Revision for each board according to Section 4-16.
The last three numbers of the program and the program revision letter appear on the display. All three boards will
match one of the rows horizontally in Table 9-1. The WFCM board will appear on the display for earlier versions of
program. This board is not used in the PipePro 300 so it can be ignored in this case. Once the board program revisions
are identified, use Table 9-1 to select the proper replacement board part number(s).
If the program revision cannot be found due to board failure, the serial number and/or knowledge of a prior update must
be used to determine the correct board number. Another welding power source at the same location may be used to
determine the program revision to remain consistent.
Table 9-1. Program Revisions For Circuit Boards
UIM AIM PCM Original
Manufacture
Starting
w/Serial No.
Stock Number
907489 907435
Software Board Board Software Board Software Board
226429D 246895 249383 226431B 238019 222230H 246554 LK310043G
226429E 247937 249384 226431B 238019 222230J 247935 MA120110G