Miller DYNASTY 200 DX Скачать руководство пользователя страница 27

Страница: 27 / 92

OM-2240 Page 21

2/04 - Ref. 802 136-A / 803 428-A

Installation must meet all National

and Local Codes

−

have only quali-

fied persons make this installation.

Disconnect and lockout/tagout in-

put power before connecting input

conductors from unit.

Always connect green or green/

yellow conductor to supply

grounding terminal first, and never

to a line terminal.

The Auto-Line circuitry in this unit au-

tomatically adapts the power source

to the primary voltage being applied.

Check input voltage available at site.

This unit can be connected to any in-

put power between 120 and 460 VAC

without removing cover to relink the

power source.

For Three-Phase Operation

Input Power Cord.

Disconnect Device (switch shown in

the OFF position)

Green Or Green/Yellow Grounding

Conductor

Disconnect Device Grounding

Terminal

Input Conductors (L1, L2 And L3)

Disconnect Device Line Terminals

Connect green or green/yellow grounding

conductor to disconnect device grounding

terminal first.
Connect input conductors L1, L2, and L3

to disconnect device line terminals.
7

Overcurrent Protection

Select type and size of overcurrent protec-

tion using Section 4-11 (fused disconnect

switch shown).
Close and secure door on disconnect

device. Remove lockout/tagout device,

and place switch in the On position.

= GND/PE Earth Ground

Tools Needed:

4-12. Connecting Three-Phase Input Power

Содержание DYNASTY 200 DX





























































































Результаты поиска

Содержание DYNASTY 200 DX

Отзывы:

Похожие инструкции для DYNASTY 200 DX

Бренды по названию

Популярные бренды

Miller DYNASTY 200 DX, Руководство пользователя

Результаты поиска

Содержание DYNASTY 200 DX

Отзывы:

Похожие инструкции для DYNASTY 200 DX

Бренды по названию

Популярные бренды