To select a generator that has enough power output in watts, add the watts
for the items you want to simultaneously run. Tools and appliances with
induction motors may require 3 – 7 times the listed wattage when starting.
All data listed is approximate — check your tool/appliance for specific
wattage requirements.
Bobcat 3 Phase will easily start and run the following equipment:
TYPICAL EQUIPMENT POWER USAGE
Equipment
Pivot Irrigation
(9–1 HP), 9 Tower
Pivot Irrigation
(6-3/4 HP, 3–1-3/4 HP, 1–1 HP),
8 Tower with Corner Arm
Starting Watts
Running Watts
Barn Cleaner
(5 HP)
11,600
3000
Silo Unloader
(5 HP)
12,200
4300
Portable Conveyor
(1/2 HP)
3400
1000
Milker
(5 HP)
10,500
2800
Hand Drill
(1/2 inch)
600
600
Circular Saw
(8-1/4 inch)
1400
1400
Air Compressor
(1-1/2 HP)
8200
2200
Flood Lights
(Vapor)
1250
1000
Refrigerator/Freezer
2200
700
Sump Pump
1300
800
Millermatic
®
212 MIG Welder
6500
6500
(30 – 210, 230 V)
Spectrum
®
625
6900
6900
(30 A, 230 V, 1/2 in cut)
The Bobcat Generator Power Advantage
Tools and motors are designed to operate within 10% of
120/240/480 VAC. The Bobcat’s power generator provides strong
power while keeping the voltage within 10% of 120/240/480 VAC.
This increases tool/motor performance and life.
Accu-Rated
™
– Not Inflated Generator Power
Miller’s Accu-Rated
™
11,000 watts of
usable peak power is delivered for a
minimum of 30 seconds. Accu-Rated means peak power is usable for
maximum generator loads such as plasma cutting, Millermatics and motor
starting. Accu-Rated peak power beats the competition’s very short-duration
peak or surge power. Use your peak power, it’s more than a number.
Smooth Power – Not Spike Power
Revolutionary ten-degree skewed-rotor design
optimizes generator performance for smoother
power—not spiked power found with other
brands. Better power — better performance.
Fuel Consumption Data
•
12-gallon fuel capacity.
•
On a typical job using 1/8-in 7018 electrodes (125 amps, 20% duty cycle)
expect about 20 hours of operation.
•
Welding at 150 amps at 40% duty cycle uses approxi mately 3/4 gallon
per hour— about 16 hours of operation.
•
Under a continuous load of 4000 watts of generator power, the Bobcat
would run for about 14 hours.
IDLE 2200 RPM
3750 RPM
1-Phase
Generator
Power
DC WELD/
3-Phase
Generator
Power
FUEL CONSUMPTION
(Kohler 23 HP Command OHV)
2.00
1.75
1.50
1.25
1.00
0.75
0.50
0.25
0
U.S. GAL/HR
0
25
50
75
100
125
150
175
200
225
250
WELD AMPS AT 100% DUTY CYCLE
0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0 10.0
POWER KVA AT 100% DUTY CYCLE
Waveform Comparison
Bobcat
Competitor
3
A.
20 in (508 mm)
B.
16-1/2 in (419 mm)
C.
1-3/4 in (44 mm)
D.
6-1/16 in (154 mm)
E.
32-3/4 in (832 mm)
F.
45-3/8 in (1153 mm) (Gas)
G.
13/32 in (10 mm) diameter
Height:
33-1/2 in (851 mm)
(to top of exhaust)
Width:
20 in (508 mm)
Depth:
45-7/8 in (1164 mm)
4 Holes
Engine End
G
A
B
C
D
E
F
Mounting Specifications
