www.milleredge.com [email protected] 800-220-3343
2/5
5.
Determine which monitored interface your operator uses:
•
10K Operator [Table 1]: Connect the
COM (C1/C2)
and the correct output connections (
BS1/BS2
) to your operator. Set
DIP switch 4
to
off
.
•
N.C. Operator [Table 2]: Connect the
COM (C1/C2)
and the correct output connections (
CS1/CS2
) to your operator. The
A Test
terminals must be used for operators requiring N.C. inputs. Set
DIP switch 4
to
on
.
6.
Turn on power to the operator. Note: it takes ~5 seconds for the Receiver to initialize.
TABLE 1. REMOVABLE CONNECTORS
ON
1 2 3 4
12/24 AC/DC
CS1 C1 BS1 CS2 C2 BS2 NO3 C3
COM.A TEST
+
-
8-PIN CONNECTOR
Power
+12/24 AC/DC
f
Constant power source
-12/24 AC/DC
f
Constant power source (ground)
Relay Output 1
CS1
f
N.C. monitored input
C1
f
Monitored input Common
BS1
f
10K monitored input
Relay Output 2
CS2
f
N.C. monitored input
C2
f
Monitored input Common
BS2
f
10K monitored input
4-PIN CONNECTOR
Relay Output 3
NO3
f
Low battery alarm (optional)
C3
f
Low battery alarm (optional)
N.C. Power Cycling
COM
f
COM: Switched power Common
A TEST
f
+12/24VDC: Switched power source
TABLE 2. NORMALLY CLOSED OPERATORS: Removable Connector Assignments by Manufacturer
HySecurity
ON
1 2 3 4
DIP Switch #4
• O
n
to run
•
Off
to test
CS1 C1 BS1 CS2 C2 BS2 NO3 C3
COM. A TEST
12/24 AC/DC
+
-
SENSOR COMMON
COMMON (not sensor common)
24 VDC
S1
S2
Ramset
ON
DIP Switch #4
•
Turn to
o
n
CS1 C1 BS1 CS2 C2 BS2 NO3 C3
COM.A TEST
12/24 AC/DC
+
-
24 VAC on terminal strip
NC
(JP13, PIN 1)
COM
(JP13, PIN 3)
VS
(JP13, PIN 5)
1 2 3 4
VS
(JP13, PIN 4)
All-O-Matic
ON
DIP Switch #4
•
Turn to
o
n
CS1 C1 BS1 CS2 C2 BS2 NO3 C3
COM.A TEST
12/24 AC/DC
+
-
+12 or 24
VDC
GR
OUND
MON_CLOSE
COMMON
MON_OPEN
COMMON
COMMON
MON-12 VDC
1 2 3 4
Maximum Controls
CS1 C1 BS1 CS2 C2 BS2 NO3 C3
COM.A TEST
12/24 AC/DC
+
-
12 or 24
VDC*
GND*
EDGE 1**
GND**
EDGE 2**
GND**
GND**
+12 VDC**
ON
1 2 3 4
DIP Switch #4
•
Turn to
o
n
NOTE
For operator software at these versions
or higher, leave
DIP switch 4
in the
on
position:
• Smart Touch Controllers (STC): h4.56
• Smat DC Controllers (SDC): h5.57
• S.T.A.R.T.:
v3.03
