background image

HV-3C

HV-3C GENERAL SPECIFICATIONS

THD + Noise, 20 Hz - 30 kHz, 35 dB gain  < .0007%, typ .002 % maximum, +27 dBu out
Frequency Response -3 dB points 

 

Sub 2 Hz to beyond 500 kHz

Frequency Response, Interchannel Deviation  < 0.1 dB
Maximum Input Level  

  

 

+23 dBu

Maximum Output Level 

 

 

+32 dBu 

Input Impedance  

 

 

 

6,200 ohms, nominal

Output Impedance    

 

 

24.3 ohms 

Noise   (Common source) 

 

 

-73 dB @ 60 dB gain (-133 dB EIN)

 

(30 ohm source) 

 

 

-71 dB @ 60 dB gain (-131 dB EIN)

 

(150 ohm source) 

 

 

-68 dB @ 60 dB gain (-128 dB EIN)

Common Mode Rejection Ratio 

 

> 70 dB @ 35 dB gain, 100 mV, to 20 kHz

 

 

 

 

 

 

> 85 dB typical

Three-pin XLR Polarity  

 

 

Pin 2 = positive polarity, Pin 1 = ground

Four-pin XLR Polarity  

 

 

Pin 1 = ground, Pin 2 = no connection

 

 

 

 

 

 

Pin 3 = +130 VDC (limited to 10 mA)

 

 

 

 

 

 

Pin 4 = unbalanced audio

ELECTRO-MECHANICAL SPECIFICATIONS

Power Consumption   

 

 

25 Watts, nominal 

Power Requirements    

 

 

100VAC to 240VAC, 50/60Hz, selectable 

Fuses (2 required) 

 

 

 

2 ea (5 x 20mm,  slow-blow, 250V)

 

 

 

 

 

 

see "Rear Panel" section of manual for values

Internal DC Power 

 

 

 

+130V, +48V, +25V,  -25V

Dimensions 

 

 

 

 

19" W x 13" D x 1.75" H 

Net Weight 

 

 

 

 

aproximately 12 pounds

Millennia Media reserves the right to change specifications, delivery, and pricing without notice.

Содержание HV-3C













Отзывы: