manualshive.com logo in svg

Millenium slow stick x, Руководство по сборке

Поделиться
Скачать
Millenium slow stick x Скачать руководство пользователя страница 4

 

4

Step-6:

 Install, 

DO NOT

 glue TE (trailing 

edge) assembly to ribs. Parts are delicate at this 
point. 

 

 
 

Step-7:

 Install, 

DO NOT

 glue 3/16" square 

spar sticks. 

Tip!

 Look straight down the sticks 

to determine natural bow. Install sticks so bow 
is opposite opposing stick’s bow. This will help 
make the wing truer. 

 

 

Step-8:

 Install, 

DO NOT

 glue LE (leading 

edge) crutch. 
 

 

 
 

Step-9:

 Install end rib W4. Square W4 to LE 

and TE then glue to TE and LE only. 

 

 
 

Step-10:

 

CAUTION! DO NOT install W1A 

upside down.

 Install W1A and B. The notch in 

the front of W1A should be facing the bottom 
(Servo Side) of the wing. Square the LE and 
TE to W1 and Glue at TE and LE. Use a small 
scrap piece of 1/16" ply to shim the space 
between SC1 and SC2-A/B. The parts should 
be shimmed such that the plywood wing joiner 
P2 should slide into the wing. 

Use extra 

caution not to glue the shims or P2 in place.

 

Use a tiny dot of medium CA to tack the spar 
sticks, SC1, SC2-A/B, W1 and W2 in place. 
Pull the shims out and test fit P2. Remove P2, 
place the wing on a flat surface so the spar is 
straight and continue tack-gluing all joints. Lift 
the wing off your work surface and use thin CA 
to glue all joints. Take caution not to glue the 
wing to your work surface or your face. LOL 

☺

 

 
 

 

 
 
 

Содержание slow stick x













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды