background image

 

Millennium

 

RC

 

presents…

 

Build Kit   

 

 
 
 
 

 
 
 
 
 
 
 
 
   
 
 

 
 
 
 
 
 

Wing

 

span:

  

Approx.

 

42”

 

Wing

 

Area:

  

504

 

sq.

 

in.

 

Wing

 

Loading:

  

6.71

 

oz/

 

sq.

 

ft.

 

 
 

Introduction: 

The Slow Stick X and X-Trainer airplanes are available either as a “short kit” upgrade to the GWS Slow Stick 
Electric ARF Park Flyer Airplane Kit ™ or as a complete kit which includes all of the fuselage components.  
The “short” kit replaces the original Styrofoam wing and tail surfaces of the Slow Stick to a more robust balsa-
constructed design, complete with ailerons and a full symmetrical wing, allowing the Slow Stick to become a 
fully aerobatic model aircraft.  This wing and tail are designed to easily attach to your existing stick fuselage.  

This build kit can be built either as a Slow Stick X (with the straight wing) or as the X-Trainer (with a 
dihedral wing). 

 The Slow Stick X is also available as a pre-built and covered ARF. 

 
Adult supervision recommended for children 15 and under.  R/C Airplanes should be flown following safety 
guidelines provided by the AMA (Academy of Model Aeronautics).   
 

CAUTION:  This is not a toy! 
 
Recommendations:

 

 

1.

 

Read through each step before starting assembly. 

2.

 

After removing all the pieces from packaging, inspect to make sure there are no broken or missing parts. 

3.

 

Check off each completed step to help keep from losing your place. 

4. 

Cover the work table with plastic wrap to protect from glue.

 

 
 
 

 

 

Содержание slow stick x













Отзывы: