background image

WINCH MAINTENANCE

TROUBLESHOOTING

• All moving parts within the electric winch have been lubricated using high temperature lithium grease at the factory. No further internal 

lubrication is required for the life of the winch.

•If using steel cable, lubricate the steel cable periodically using light penetrating oil
• Electrical connections may corrode over a period of time due to environmental changes. This may result in reduced performance of the winch  

or even possible electrical shorting. Hence, always clean the electrical connections before and after using the winch.

•After every use of the winch, inspect the steel cable/synthetic rope for damages such as kinks, broken strands etc. When damaged, replace the 
  cable immediately.

Symptom

Possible Cause

Suggested Remedy

Motor does not turn on

Safety switch is OFF

Turn safety switch ON

Switch assembly not connected 
properly

Insert switch assembly firmly to the connector

Loose battery cable

Tighten nuts on cable connectors

- Connection  
- Solenoid malfunctioning 

Tap solenoid to free contact, applying 12 volts 
to coil terminal directly.  An audible clicking 
will occur when activating.

Defective switch assembly

Replace switch assembly

Defective motor

Check for voltage at armature port with switch 
pressed.  If voltage is present,
replace motor.

Water has entered motor

Drain and dry.  Run in short bursts without load 
until completely dry.

Motor runs too hot

Long period of operation

Let winch cool down periodically

Motor runs slowly or 
without normal power

Battery runs down

Recharge battery by running vehicle engine

Insufficient current or voltage

Clean, tighten or replace the connector

Motor runs but cable 
drum does not turn

Clutch not engaged

Turn clutch gear to IN/ENGAGED position - if 
that does not work, ask a qualified technician 
to check and repair

Motor runs in one 
direction only

Defective or stuck solenoid

Tap solenoid to free contacts. Repair or replace 
solenoid.

Defective switch assembly

Replace switch assembly

2121 Blount Road Pompano Beach, FL 33069        MileMarker.com        1.800.886.8647

PAGE 11

Содержание 76-50246BW





















Отзывы: