background image

10 Menu Functions

11 Maintenance

Maxi - The filter which is housed in the inlet ball valve to the pump should be checked and cleaned annually.

EXPANSION VESSELS - Charge pressure should be checked annually, when the system is cold the air charge must be 

equal to the cold fill pressure of the Maxi.

13

Cold fill pressure - this is the required pressure of the system when the system is cold

Alarm low - the pressure at which the low pressure alarm relay will operate. Usually set 0.6 - 0.7 bar below

the cold fill pressure. 

Alarm high - the pressure at which the high pressure alarm relay will operate. Usually set 0.2 bar below the

system safety valve setting.

Usage - for information on water used in the system, no setting required - please note, to zero the usage, the

buttons need to be pressed simultaneously for 3 seconds.

minutes ) the less responsive the flood protection, set at 0.00 to disable pump failure.

prevents under shoot, decreasing time prevents over shoot.

Frequent use - this setting warns of frequent use which would indicate a system leak and will show a 

warning message if in any 24hr period the unit operates in excess of the frequent use setting.

caused when pumps start.

Contrast adjust - alters the contrast of the LCD display.

O&M Maxi 1109

Fault log - Logs the last five faults

MP - Low mains water pressure

LP - Low system pressure alarm

HP - High system pressure alarm

SF - Sensor failure

DR - Leak alert due to no increase in pressure while filling

FS - Leak alert due to drop in pressure while filling

Содержание Maxi Plus

















Отзывы: