Miele WTD 160 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 10

Miele WTD 160 Скачать руководство пользователя страница 6

11694001-01

Installation

*INSTALLATION*

Levelling the washer-dryer

The washer-dryer must stand perfectly
level on all four feet to ensure safe and
proper operation.

Incorrect installation may increase
electricity and water consumption and
may cause the machine to move about.



The appliance must not be

installed behind a lockable door, a
sliding door or a door with a hinge on
the opposite side to that of the
appliance, in such a way that a full
opening of the appliance door is
restricted.

Screwing out and adjusting the feet

The 4 adjustable feet are used to level
the washer-dryer. All four feet are
screwed in when the appliance is
delivered.



Using the spanner supplied, turn
counter nut

2

in a clockwise direction.

Then turn counter nut

2

together with

foot

1

to unscrew.



Use a spirit level to check the
washer-dryer is standing level.



Hold foot

1

securely with a pipe

wrench. Turn counter nut

2

again

using the spanner supplied until it sits
firmly up against the housing.



Risk of damage from incorrectly

aligned washer-dryer.
There is a danger of the washer-
dryer moving about if the feet are not
secured.
Turn all 4 counter nuts for the feet
until they sit firmly up against the
casing. Please also check this for the
feet which did not need adjustment.

«
...
4
5
6
7
8
...
»

Содержание WTD 160











Отзывы:

Нет отзывов