background image

WARNING

Read all instructions before installation or
use to prevent injury and machine dama-
ge.

This washer-extractor is only intended for
laundry not impregnated with dangerous
or flammable substances.

Dry cleaning solvents

must not

be used

in this machine. Such solvents could cau-
se a fire or explosion.

This appliance conforms to all uniform sa-
fety codes and regulations. The manufac-
turer cannot be held responsible for
damage or injury caused by improper use
of this appliance.

All personnel working with this machine
must be fully trained in its use and safety.

SAVE THESE INSTRUCTIONS AND RE-
VIEW THEM PERIODICALLY

Electrical Safety

Installation, repair and maintenance
work should be by a Miele authorized

service technician. Work by unqualified per-
sons could be dangerous.

Before installation make sure that the
voltage and frequency listed on the

data plate correspond with the site electrical
supply. This data must correspond to pre-
vent injury and machine damage. Consult a
qualified electrician if in doubt.

Be certain your appliance is properly in-
stalled and grounded by a qualified

technician.
To guarantee the electrical safety of this ap-
pliance, continuity must exist between the
appliance and an effective grounding sys-
tem. It is imperative that this basic safety re-
quirement be met. If there is any doubt, have
the electrical system of the house checked
by a qualified electrician. The manufacturer
cannot be held responsible for damages
caused by the lack, or inadequacy of, an ef-
fective grounding system.

The appliance is only completely isola-
ted from the electrical supply when the

fuse is withdrawn, the circuit breaker has
been tripped, or the unit has been unplug-
ged.

Do not damage, remove or bypass the
safety features and controls of the ma-

chine.

If there is any damage to the machine
or to the cable insulation, the machine

must not be used until it has been repaired.

Any removable outer panels must be in
place, and all moving or electrical parts

shielded before the machine is operated.

Use

Never use or store gasoline or gasoline
based substances or any easily flam-

mable substances near the machine. Do not
use the machine lid as a storage area.

Danger of fire or explosion.

Only machine wash articles with a care
label stating they are suitable for machi-

ne washing.

Never attempt to force open the door of
the washer extractor. As a safety feature

the door handle has been designed with a
break line.

Never allow children to play in, on or
near the washer extractor, or to operate

it themselves. Please supervise its use by
the elderly or infirm.

The door porthole glass can become
hot during use of the machine. Do not

allow children to touch the glass.

Always make sure the drum is stationa-
ry before reaching in to remove laundry.

Reaching into a moving drum is extremely
dangerous.

Waste water from washing and rinsing
must not be used as drinking water. It

must be discharged into a proper sewage
system.

The machine should only be operated
unsupervised if there is a floor drain

(gully) in the direct vicinity of the machine.

Warning and Safety Instructions

3

Содержание WS 5101

































Отзывы: