background image

The Miele "Water protection
system" protects from water

damage provided the following
conditions have been met:

– the machine is correctly plumbed in

and connected to the electricity
supply.

– if a fault has been identified, the

machine must be examined by a
competent person before further use,
and repaired if necessary.

Faulty components must only be
replaced by genuine Miele original

spare parts. Only when these parts are
fitted can the safety standards of the
machine be guaranteed.

If the connection cable is faulty it
must only be replaced by a Miele

approved service technician to protect
the user from danger.

In countries where there are areas
which may be subject to infestation

by cockroaches or other vermin, pay
particular attention to keeping the
machine and its surroundings in a
clean condition at all times. Any
damage which may be caused by
cockroaches or other vermin will not be
covered by the guarantee.

Use

This equipment may only be used
in mobile installations such as

ships, caravans, aircraft etc. if a risk
assessment of the installation has been
carried out by a suitably qualified
engineer.

Do not install your washing
machine in rooms where

temperatures below freezing may
occur. Frozen hoses may burst or split.
The reliability of the electronic control
unit may be impaired at temperatures
below freezing point.

Before using the machine for the
first time, check that the transit

fittings at the rear of the machine have
been removed (see section on
"Installation"). During spinning, a transit
fitting which is still in place may result in
damage to both the machine and
adjacent furniture or appliances.

Turn off the stopcock if the
machine is to be left for any length

of time (e.g. holiday), especially if there
is no floor drain (gully) in the immediate
vicinity.

Flooding danger
If hooking the drain hose into a

wash basin, check that the water can
drain off quickly enough to prevent the
sink from overflowing.
Make sure the drain hose is secure, so
that the force of the water flowing out of
the hose does not dislodge it.

Take care to ensure that foreign
objects (e.g. nails, pins, coins,

paper clips) do not find their way into
the machine with the laundry. These
may damage components of the
machine (e.g. suds container, drum),
which in turn can result in damage to
the laundry.

Warning and safety instructions

7

Содержание W 3364 WPS

































































Отзывы: