Miele TDA 140 C Скачать руководство пользователя страница 26

Страница: 26 / 60

Cleaning and care

Cleaning the condenser unit

Check the condenser unit at least

once a year. If the dryer is used

frequently, then clean the condenser

unit on a regular basis.
Always check the fluff filters and the

condenser unit if the

Clean out

airways

indicator light comes on.

Detergent residue, hair and fine fluff

from the dryer can get through the

fluff filters and block the condenser

unit. Dust from the room in which the

dryer is installed can also get into the

condenser unit and cause a blockage.

Removing the condenser unit



Use the yellow lever supplied to open

the service panel.



Insert the lever into the middle of the

gap in the top (see arrow) and lever

the panel until it opens at the top.



Now remove the panel by pulling it

diagonally upwards. Then place it to

one side.



Turn the lever on the inner cover

downwards to the vertical position.



Pull the cover forwards.



Then remove it by pulling it diagonally

upwards.



Turn the lever on the condenser unit

to the vertical position so that the

hook on the lever is no longer in the

groove at the bottom of the

condenser unit housing.

Содержание TDA 140 C





























































Результаты поиска

Содержание TDA 140 C

Отзывы:

Похожие инструкции для TDA 140 C

Бренды по названию

Популярные бренды

Miele TDA 140 C, Руководство по эксплуатации

Результаты поиска

Содержание TDA 140 C

Отзывы:

Похожие инструкции для TDA 140 C

Бренды по названию

Популярные бренды