Miele T 8903 C Скачать руководство пользователя страница 43

Страница: 43 / 48

Switching the buzzer on/off

A buzzer sounds (at intervals for a
maximum of 1 hr) to let you know the
programme has finished.

The buzzer is activated as standard at
the factory. You can deactivate the
buzzer at the end of a programme if
you wish.

The buzzer will still sound if there is a
fault, even if it has been switched off.

Follow steps (

...) with the

help of the

Start

button and

programme selector to programme
and store in memory.

Before you begin, first ensure that:

– The dryer is switched off.

– The door is closed.

– The programme selector is turned to

Finish

Press the

Start/Stop

button and keep

it pressed in whilst carrying out steps

Switch the dryer on.

Wait until

Start

lights up

constantly. . .

. . . and then release the

Start

button.

Turn the programme selector to

Cottons Low temperature

The

Finish/Anti-crease

indicator light

will flash four times.

The

flashing

Drying

indicator light

shows which option is selected.

– The

Drying

indicator light doesn't

flash:

Buzzer is switched off.

– The

Drying

indicator light flashes:

Factory default setting. Buzzer is
switched on.

You can switch from one option to
the other by pressing the

Start

button

(

Drying

indicator light).

Switch the dryer off.

The setting you have selected is now
stored in memory. You can alter the
settings again at any time.

Control

Repeat steps

After checking the indicator lights
(see above), switch the dryer off.

Programmable functions

Содержание T 8903 C

















































Результаты поиска

Содержание T 8903 C

Отзывы:

Похожие инструкции для T 8903 C

Бренды по названию

Популярные бренды

Miele T 8903 C, Руководство по эксплуатации

Результаты поиска

Содержание T 8903 C

Отзывы:

Похожие инструкции для T 8903 C

Бренды по названию

Популярные бренды