Miele T 8433 C страница 21 Скачать руководство пользователя

Страница: 21 / 56

Once a programme has started

- changing the programme

You cannot change to another
programme once a programme has
started (this prevents unintentional
alterations).

It is still possible to select or deselect
the

Buzzer

and the

Anti-crease

extra

option.

You will need to cancel the current
programme before you can select a
new one.

- cancelling the programme and then
selecting a different programme

Press the

Start/Stop

button.

The items will be cooled down,
depending on the temperature
reached and how long they have
been dried for.

The programme will be cancelled if
you press the

Start/Stop

button again

during the cooling down phase.

Switch the dryer off.

Switch the dryer on.

Select another programme and start
it.

- cancelling the programme and then
removing the laundry

Proceed as described in "Adding or
removing laundry after a programme
has started" below.

Switch the dryer off after closing the
door.

Adding or removing laundry
after a programme has started

Press the

Door

button.

Open the door.

Danger of burning:

Do not touch the back of the drum
when adding or removing items. The
drum and the items can get very hot.

Add or remove items as required.

Close the door.

Press the

Start/Stop

button.

Time remaining

The time left shown in the display may
now vary from the actual drying time.

Changing the programme sequence

Содержание T 8433 C

























































Результаты поиска

Содержание T 8433 C

Отзывы:

Похожие инструкции для T 8433 C

Бренды по названию

Популярные бренды

Miele T 8433 C, Руководство по эксплуатации

Результаты поиска

Содержание T 8433 C

Отзывы:

Похожие инструкции для T 8433 C

Бренды по названию

Популярные бренды