Miele T 7744 C Скачать руководство пользователя страница 50

Страница: 50 / 52

Keypad tone

An audible tone sounds each time a
button is pressed.

Follow steps

to programme

and store in memory.

Before you begin, first ensure that:

–

The tumble dryer is switched off.

–

The door is closed.

Press the

Start/Stop

button and keep

it pressed in whilst carrying out steps

Press the

I-On/0-Off

button in.

Wait until the indicator light for the

Start/Stop

button lights up

constantly . . .

. . . and then release the

Start/Stop

button.

Press the

Low temperature

button

five times.

–

The

Low temperature

indicator light

will flash on and off slowly once and
will then flash on and off quickly
once.

–

and

(default setting) will flash

alternately in the display.

The number which appears alternately
in the display with

means:

Keypad tone deactivated

(Default setting)

Keypad tone activated

(The

Automatic

indicator light will

also flash)

Pressing the

Start/Stop

button

switches from one to the other.

Switch the dryer off with the

I-On/0-Off

button.

The setting you have selected is now
stored in memory. You can change it
again at any time.

Programmable functions

Содержание T 7744 C





















































Результаты поиска

Содержание T 7744 C

Отзывы:

Похожие инструкции для T 7744 C

Бренды по названию

Популярные бренды

Miele T 7744 C, Руководство по эксплуатации

Результаты поиска

Содержание T 7744 C

Отзывы:

Похожие инструкции для T 7744 C

Бренды по названию

Популярные бренды