Miele T 4819 Ci Скачать руководство пользователя страница 27

Cleaning the fluff filters

The fluff which is created by the drying
process is collected by the fluff filters in
the door and the door opening. Clean
the filters after

each

drying

programme*.

Cleaning them whilst dry

Tip: You can also use a vacuum
cleaner to remove the fluff.

^

Open the door and pull the fluff filter
(1) out of the door as illustrated.

^

Use your fingers to remove the fluff
from the surface of the filter.

^

Remove any fluff from the hollow part
of the door opening. You could also
use a cleaning brush which is
available as an optional extra from
your Miele dealer or the Miele Spare
Parts Department, or use a vacuum
cleaner.

^

Also clean the door seal (2) with a
damp cloth.

^

Once clean, push the filter back into
the door holder until it clicks into
position. Ensure it is facing the
correct way.

^

Use your fingers or a vacuum cleaner
to remove the fluff from the two fluff
filters in the door opening.

^

Close the door.

* Always check the fluff filters if the

Clean out airways

indicator light

comes on.

Cleaning and care

27

Содержание T 4819 Ci





































































Отзывы: