Miele T 4672 C Скачать руководство пользователя страница 32

Страница: 32 / 52

Problem

Possible cause

Remedy

The following
message
appears after
the programme
has finished:

Clean the filters

Air is not flowing freely
through the dryer.

–

The dryer is not working
efficiently or
economically.

–

Possible causes: The fluff
filters are clogged with
fluff or with detergent
residues.

–

Clean the fluff filters.
If they need to be cleaned
with water, make sure they
are completely dry before
replacing them.

–

See also the notes on the
next page under: "The drying
process goes on too long or
even switches off".

To delete the fault message:

–

Switch the dryer off and then
back on again.

You can adjust the setting
which controls when or if
the message

Clean the

filters

appears.

See Settings menu

, Airways

indicator section.

Technical fault
Call the Service
Department

No obvious cause.

In some circumstances,

Clean the filters

will already

have been displayed.

–

Clean the fluff filters and the
condenser unit.

To delete the fault message:

–

Switch the dryer off and then
back on again.

There is a fault, if despite
doing this, the programme
is cancelled and the fault
message appears again.

Contact the Miele Service
Department.

Programme
cannot
be changed

An attempt has been made
to alter a programme while
it is in progress.

You will need to cancel the
current programme before you
can select a new one.

Programme finish
time changed

This is not a fault.

Settings were changed during a
delay start period, or there has
been a power cut.

Problem solving guide

Содержание T 4672 C





















































Результаты поиска

Содержание T 4672 C

Отзывы:

Похожие инструкции для T 4672 C

Бренды по названию

Популярные бренды

Miele T 4672 C, Руководство по эксплуатации

Результаты поиска

Содержание T 4672 C

Отзывы:

Похожие инструкции для T 4672 C

Бренды по названию

Популярные бренды