manualshive.com logo in svg

Miele T 4659 Ci, Руководство по эксплуатации

Поделиться
Скачать
Miele T 4659 Ci Скачать руководство пользователя страница 38

Installation site

,

Make sure the dryer door can be

opened without hindrance after
installation.

Building under a continous worktop /
in a kitchen run

This machine is specially designed for
installation under a continuous worktop
run in a fitted kitchen.

N

= Niche height (820-930 mm)

It is supplied fitted with a cover plate
instead of a machine lid. The cover
plate is necessary to ensure
electrical safety and must not be
removed.

– The slides supplied should be used

to protect the floor from damage
when the machine is pushed into
position or taken out for servicing.

– The electrical socket must be

located in an accessible position
near the machine.

With niche heights of:

– 840 mm, longer screw feet* are

required. They should be set at a
height of approx. 40mm.

– 870/885 mm - 915/930 mm, one or

two height adjustment frames* are
required.

* optional accessory

The machine must not be used
without the front panel in place.

If the kitchen run has a continuous
furniture plinth in place, a gap must
be made for the tumble dryer.

Installation

38

Содержание T 4659 Ci





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды