Miele PW 6065 Vario Скачать руководство пользователя страница 41

Страница: 41 / 64

A fault message appears in the display

Message in the display

Possible cause

Remedy

Water intake fault
Open the stopcock
and
check the inlet hose.

The water inlet is
blocked or restricted.

Check whether

– the stopcock is opened

enough.

– the inlet hose is kinked.

The water pressure is
too low.

Select

Low water pressure

the

Settings/Supervisor level

menu.

Technical fault

There is a fault.

Start the programme again.
If the fault message appears
again, contact the Service
Department.

Fault
Disinfection
temperature
not reached

During the
disinfection pro-
gramme the water
temperature was not
reached.

The machine has

not

carried

out the disinfection cycle
correctly.
Start the programme again.

Drain fault
Clean the drainage
system.

The water outlet is
blocked or restricted.

LP version: Clean the
drainage system.

AV version: Call the Service
Department.

Waterproof system
fault

The water protection
system has reacted.

Close the stopcock.

Call the Service Department.

Fill the container

One of the external
detergent containers
is empty.

See "Detergent - Empty
sensor".

Fault
Container empty

To switch off the fault message, press the multi function selector.

Problem solving guide

Содержание PW 6065 Vario

































































Результаты поиска

Содержание PW 6065 Vario

Отзывы:

Похожие инструкции для PW 6065 Vario

Бренды по названию

Популярные бренды

Miele PW 6065 Vario, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание PW 6065 Vario

Отзывы:

Похожие инструкции для PW 6065 Vario

Бренды по названию

Популярные бренды