Miele KFN 37432 iD Скачать руководство пользователя страница 48

Страница: 48 / 104

Adjusting the interior fittings

Moving the charcoal filters

Charcoal filters and a KKF-FF (Active
AirClean) holder are available as
optional accessories (see
“Accessories - optional accessories”).

When storing very strong smelling
food (e.g. very ripe cheese):

– Place the holder with the charcoal

filters on the shelf where this food is
kept.

– Change the filters sooner if

necessary.

– Use more charcoal filters (with

holders) in the appliance (see
“Accessories – Optional
accessories”).

The holder for the charcoal filters sits
on the protective strip at the back of the
shelf.



To move the charcoal filters, pull the
holder upwards to remove it from the
protective strip.



Refit the holder on the protective strip
of the shelf you wish to use it on.

Содержание KFN 37432 iD









































































































Результаты поиска

Содержание KFN 37432 iD

Отзывы:

Похожие инструкции для KFN 37432 iD

Бренды по названию

Популярные бренды

Miele KFN 37432 iD, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание KFN 37432 iD

Отзывы:

Похожие инструкции для KFN 37432 iD

Бренды по названию

Популярные бренды