background image

Stainless steel panels

Stainless steel door panels and toe-kick
covers are available from Miele.

Custom door panels

This appliance is compatible with all
styles and designs of kitchen cabinetry.

The total weight of the decorative
panel(s) must not exceed the following:

K 18x3 Vi

. . . . . . . . . . . . 110 lbs (50 kg)

K 19x3 Vi

. . . . . . . . . . . . . 81 lbs (37 kg)

Installation options

There are many different installation
options. These are limited only by the
design of the kitchen.

The door hinge cannot be
exchanged.

Single column

The appliance can be installed at any
preferred location in the kitchen.

However, be sure the door will open
and close properly in the chosen
location.

Side-by-side

This appliance can be installed
"side-by-side" with another
fridge/freezer using a "Merging Kit".

The "Merging Kit" is available from
Miele.

Contact Miele or your dealer for
specific information about which
combinations will work with your
appliance.

For instructions on how to attach the
appliances and install the heating
mat, please refer to the instructions
included with the "Merging Kit",
available from Miele.

Installation without a partition using
the "Merging Kit"

If the appliances are installed directly
next to each other (without a partition),
they need to be attached together
using the "Merging Kit".

Installation

40

Содержание K 1803 Vi







































Отзывы: