Miele Independence F1801Vi Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 64

Miele Independence F1801Vi Скачать руководство пользователя страница 45

If the indicator light does not come on,
installation of the module was
unsuccessful. In that case, repeat the
process. If that does not correct the
problem, contact Miele.

^

Pull the antenna

d

straight out.

^

Guide the cover

b

over the antenna

d

and screw on the cover.

^

Angle the antenna

d

so that it faces

to the right or left.

^

If necessary, disconnect the power
supply and continue installing the
appliance.

Preparing the installation
niche

Keep the appliance door closed
until it is securely fastened in the
niche. Tipping hazard.

If the installation niche is deeper than
the appliance, a solid wooden beam

a

can be placed behind the anti-tip
brackets

b

so the appliance can be

securely attached to the base or wall.

The length of the wooden beam

a

should be to the width of the installation
space.

If possible, always screw the
wooden beam into existing studs.

Installing the appliance

45

«
...
43
44
45
46
47
...
»

Содержание Independence F1801Vi

































































Отзывы:

Нет отзывов