Miele HG07-W Скачать руководство пользователя

Страница: 32 / 124

Before using for the first time

Adding rinse aid



Press the yellow button



on the lid

of the rinse aid reservoir.

The lid will spring open.



Fill with rinse aid until the filling level
indicator (arrow) changes to a dark
colour while the door is horizontally
open.

The rinse aid reservoir holds
approximately 110 ml.



Close the lid firmly until you hear it
click into place. Otherwise, water can
enter the rinse aid reservoir during a
programme.



Wipe up any spilled rinse aid. This
prevents excess foam developing
during the next programme.

You can adjust the rinse aid dosage
for the best wash result (see
“Settings” chapter, “Rinse aid”
section).

Filling the rinse aid reservoir

When the refill reminder



Refill rinse aid

appears in the display, the reservoir
contains sufficient rinse aid for 2 to 3
programmes only.



Refill with rinse aid in plenty of time.



Confirm with

The rinse aid refill reminder will
disappear.

Содержание HG07-W





























































































































Результаты поиска

Содержание HG07-W

Отзывы:

Похожие инструкции для HG07-W

Бренды по названию

Популярные бренды

Miele HG07-W, Руководство по эксплуатации

Результаты поиска

Содержание HG07-W

Отзывы:

Похожие инструкции для HG07-W

Бренды по названию

Популярные бренды